查看“MY-IMX6-EK140P L4115 测试手册”的源代码

<div>

== '''网口测试( test of network interface)''' ==

接口属性(interface property)
<br>
{| class="wikitable"
|评估板型号
(evaluation board model)	
|CPU接口
(CPU interface)	
|系统接口
(system interface)	
|接口丝印
(interface silk screen)
|-
|MY-IMX6-EK140	
|ENET1	
|eth0	
|P10
|-
|MY-IMX6-EK140	
|ENET1	
|eth1	
|P8
|}

测试方法(test method)<br>
1） 配置计算机IP<br>
configure computer IP<br>
设置计算机有线网卡IP为192.168.18.18<br>
set IP of cable network interface card for computer as 192.168.18.18<br>
<br>
[[文件:MY-IMX6-ek140p L41115 1.1 .jpg|520px]]<br>
2） Eth0连接测试<br>
Eth0 test for Wth0 connection<br>
连接网线：将评估板“eth0”对应的接口与计算机有线网卡的接口用网线相连接<br>
lan line connection:connect interface corresponding to “eth0”on evaluation board with interface of cable network interface card on computer through lan line<br>
设置评估板IP：<br>
set IP for evaluation board<br>
＃ ifconfig eth0 192.168.18.36 ＃ configure the eth0<br>
执行测试命令：<br>
execute test command<br>
＃ ping 192.168.18.18 -c 2 -w 4 ＃ send ICMP to HOST<br>
观察测试结果：系统会输出类似如下信息：<br>
view test result,you can see information outputed by system like below<br>
--- 192.168.18.18 ping statistics ---<br>
2packets transmitted, 2 packets received, 0% packet loss<br>
测试结果：“0% packet loss”表示测试通过<br>
test reuslt:“0% packet loss” represent passing of test<br>
<br>
附图<br>
figures<br>
[[文件:MY-IMX6-ek140p L41115_1.2.jpg|642px]]
<br>
<br>
3）eth1测试同eth0<br>



== '''USB测试(USB test)''' ==

接口属性(interface property)
<br>
{| class="wikitable"
|评估板型号
(evaluation board model)	
|CPU接口
(CPU interface)	
|系统接口
(system interface)	
|接口丝印
(interface silk screen)
|-
|rowspan=2|MY-IMX6-EK140	
|USB_OTG1	
|USB OTG	
|P18
|-	
|USB_OTG2	
|USB HOST	
|P20
|}
USB OTG测试(USB OTG test)<br>
1） 将MicroUSB转USB的转接线连接到USB1，系统会输出类似如下信息：<br>
connect to USB1 with USB switch wiring from MicroUSB,system will output information like below.<br>
ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 2<br>
ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00<br>
2） 连接USB设备。即：将U盘插入转接线上的USB口，系统会输出类似如下信息：<br>
connect USB device,e.g insert U disk to USD port on the switch wiring,system will output information like below.<br>
usb 2-1: new high-speed USB device number 12 using ci_hdrc<br>
usb-storage 2-1:1.0: USB Mass Storage device detected<br>
3） 拔出USB设备，系统会输出类似如下信息：<br>
take out USB device,system will output information like below.<br>
usb 2-1: USB disconnect, device number 12<br>
4） 拔下USB转接线，系统会输出类似如下信息：<br>
take out USB switch wiring,system will output information like below.<br>
ci_hdrc ci_hdrc.0: remove, state 4<br>
usb usb2: USB disconnect, device number 1<br>
ci_hdrc ci_hdrc.0: USB bus 2 deregistered<br>
<br>
USB HOST测试(USB HOST test)<br>
　　MY-IMX6-EK140 的USB HOST是插座形式，如要测试HOST功能，需要把自备USB头，并且将插座上的USB HOST信号线连接到USB头，此操作请找自己的硬件工程师请求支持。<br>
　　MY-IMX6-EK140 USB HOST is socket type，if need to test the function of HOST，need to connect signal line of USB HOST to the USB head self-prepared，?the operation need an assistance from hardware engineer.<br>
　　另外，请硬件工程师知晓，由于CPU的USB_VBUS供电能力不足，需要将“5V_core”与USB_VBUS相连。<br>
　　Moreover，please let engineer know that power supply capability of CPU的USB_VBUS is not enough，so need to connect“5V_core”with USB_VBUS<br>
<br>
附图(figure)<br>
<br>
[[文件:MY-IMX6-ek140p L41115_2.1.jpg|642px]]
<br>
<br>
<br>
[[文件:MY-IMX6-ek140p L41115_2.2.jpg|642px]]
<br>
<br>
<br>
[[文件:MY-IMX6-ek140p L41115_2.3.jpg|642px]]
<br>
<br>
<br>
[[文件:MY-IMX6-ek140p L41115_2.4.jpg|642px]]
== '''SD卡测试(SD card test)''' ==

接口属性(interface property)
<br>
{| class="wikitable"
|评估板型号
(evaluation board model)	
|CPU接口
(CPU interface)	
|系统设备
(system device)	
|接口丝印
(interface silk screen)
|-
|MY-IMX6-EK140	
|SD1	
|mmc0	
|U15
|}
测试说明(test instruction)<br>
MY-IMX6-EK140的TF卡接口不支持热插拔。<br>
MY-IMX6-EK140的TF card interface doesn't support hot plug<br>
<br>
测试方法(test method)<br>
1）为MY-IMX6-EK140断电。<br>
power off MY-IMX6-EK140<br>
2）将TF卡安装好板子的TF卡座上，并确认安装好。<br>
install TF card in TF card holder,and confirm the installation ok<br>
3）为MY-IMX6-EK140上电，待系统启动完成后进入系统。<br>
power on MY-IMX6-EK140,enter the system after booting is finished<br>
5）检查TF卡：<br>
check TF card<br>
＃ dmesg | grep "mmc0"<br>
TF卡正常则可以看到类似如下信息：<br>
if IF card is normal, then you can see information like below.<br>
mmc0: host does not support reading read-only switch. assuming write-enable.<br>
mmc0: new high speed SD card at address 0002<br>
<br>
附图(figure)<br>
<br>
[[文件:MY-IMX6-ek140p L41115_3.1.jpg|642px]]


== '''标准GPIO测试(standard GPIO test)''' ==

接口属性(interface property)
<br>
{| class="wikitable"
|评估板型号
(evaluation board model)	
|CPU接口
(CPU interface)	
| 系统设备
(system device)
|信号名称
(name of signal)	
|接口位置
(interface position)
|-
|rowspan=2|MY-IMX6-EK140	
|SNVS_TAMPER4	
|gpio132	
|SNVS_TAMPER4	
|P21:17
|-	
|SNVS_TAMPER8	
|gpio136	
|SNVS_TAMPER8	
|P21:15
|}
测试说明(test instruction)<br>
标准GPIO的测试以GPIO132为例，其它GPIO测试可参照GPIO132的测试方法。<br>
take GPIO132 as an example of standard GPIO test,other GPIO tests refer to the test method of GPIO132<br>
<br>
测试方法(test method)<br>
1）设置需要测试的GPIO的IO序号<br>
set IO order number of GPIO which need to be tested<br>
＃ OUT_IO_NUMBER=132<br>
2）导出GPIO<br>
lead out GPIO<br>
＃ echo ${OUT_IO_NUMBER} > /sys/class/gpio/export<br>
3）设置GPIO方向<br>
set direction for GPIO<br>
＃ echo "out" > /sys/class/gpio/gpio${OUT_IO_NUMBER}/direction<br>
4）控制输出电平<br>
control output electrical level<br>
＃ echo 0 > /sys/class/gpio/gpio${OUT_IO_NUMBER}/value<br>
执行命令后即可用万用表检测到对应的引脚为低电平。<br>
leads detected by multimeter accordingly will be low electrical level after execution of command<br>
＃ echo 1 > /sys/class/gpio/gpio${OUT_IO_NUMBER}/value<br>
执行命令后即可用万用表检测到对应的引脚为高电平。<br>
leads detected by multimeter accordingly will be high electrical level after execution of command<br>


== '''串口测试''' ==

1.测试说明<br>
采用串口自发自收测试。<br>
串口属性：<br>
{| class="wikitable"
|评估板型号	
|UARTx	
|TX	
|RX	
|系统接口
|-
|rowspan=2|MY-IMX6-EK140P	
|UART3	
|P21:26	
|P21:25	
|ttymxc2
|-	
|UART2	
|P21:28	
|P21:27	
|ttymxc1
|}
提示：这里只列出测试串口的收发管脚，串口的其他管脚的定义请看原理图。<br>
2.测试方法<br>
(1)进入测试程序目录<br>
＃ cd /home/root/my-demo/linux-4.1.15/<br>
(2)短接P21的26管脚和25管脚。<br>
(3)./uart_test.out /dev/ttymxc2 “www.myzr.com.cn”<br>
测试结果：<br>
<br>
[[文件:MY-IMX6-ek140p L41115_5.1.jpg|642px]]


== '''CAN测试''' ==
1.测试说明<br>
　　 　　MY-IMX6-EK140P上有两组CAN接口。<br>
{| class="wikitable"
|评估板型号	
|CANx	
|信号：CAN_L	
|信号：CAN_H	
|系统设备
|-
|rowspan=2|MY-IMX6-EK140P	
|CAN1	
|P7:1	
|P7:2	
|can1
|-	
|CAN2	
|P9:1	
|P9:2	
|can2
|}
采用CAN1发送，CAN0接收的方式。<br>
2.测试方法<br>
(1)将CAN1的CAN_L与CAN2的CAN_L连接；将CAN1的CAN_H与CAN2的CAN_H连接。<br>
(2)＃ ip link set can0 up type can bitrate 125000<br>
(3)＃ ip link set can1 up type can bitrate 125000<br>
(4)＃ candump can0 &<br>
(5)＃ cansend can1 1F334455＃1122334455667788<br>
测试结果：<br>
<br>
[[文件:MY-IMX6-ek140p L41115_6.1.jpg|642px]]
== '''WIFI测试''' ==
1.测试方法<br>
(1)insmod /home/root/my-demo/linux-3.14.52/8188eu.ko<br>
(2)wpa_passphrase WIFI名称 WIFI密码 > /etc/wpa_supplicant.conf<br>
(3)wpa_supplicant -Dwext -iwlan0 -c/etc/wpa_supplicant.conf -B<br>
(4)udhcpc -i wlan0<br>
(5)Ping 百度的ip，如果能ping通，说明测试成功。<br>

== '''FXLS8471测试''' ==
1.测试方法<br>
(1)# echo 1 > /sys/class/misc/FreescaleAccelerometer/enable<br>
(2)获取传感器数据：<br>
＃ cat /sys/class/misc/FreescaleAccelerometer/data<br>



== '''MAG3110测试''' ==
(1)# echo 1 > /sys/class/misc/FreescaleGyroscope/enable<br>
(2)# evtest<br>
[[文件:MY-IMX6-ek140p L41115_9.1.jpg|642px]]<br>
选择“fxas2100x”对应的event0.　<br>
(3)输入 0<br>
(4)会有数据输出<br>
</div>