查看“MYZR-LS1012A-EK200 Startup Manual”的源代码


[^ _ ^]:
MY-LS1012A-EK200 Startup Manual
    
<br/>

### MY-LS1012A-EK200 Packing list

-------------------------------------------------- ------------------------------
#### Standard Parts
[Backplane]: MY-LS1012A-MB200, 1 piece
[Core board]: MY-LS1012A-CB200, 1 piece
[Power adapter]: 5V, 1
[Network cable]: 1
[Serial cable]: 1
#### User-owned spare parts
[Mini USB cable]: 1 for download (usually used Android phone data cable can be used)
[USB to serial cable]: 1 for debugging (if the computer does not have a DB9 serial port, you need to prepare it yourself)
<br/>

### MY-LS1012A-EK200 Main Interface

-------------------------------------------------- ------------------------------

<br/>

### Development board connection

-------------------------------------------------- ------------------------------
#### Check the power switch
Press "o" of the power switch "SWITCH" of the development board to ensure that the power switch of the development board is in the off state.
#### Connection of serial cable
Connect one end of the serial cable to the "DEBUG" port of the development board, and connect the other end to the computer's serial port or USB port.
Reference ** [[Terminal Software XShell Reference Manual]] ** Create a new serial port session and open the session.
#### Network cable connection
Connect one end of the network cable to "ETH1" and the other end to the network port of the computer.
#### USB download cable connection
Connect one end of the Mini USB cable to the K20-JTAG module, and the other end to the rear USB port of the computer.
#### Connection of power cord
Connect one end of the power adapter to the "5V_IN" of the development board, and plug the other end into the mains (220V AC) socket.
#### Connection of K20-JTAG module
Connect the K20-JTAG module to the J8 interface of the development board, and the other end to a miniUSB cable
<br/>
### Start development board

-------------------------------------------------- ------------------------------
#### Check the startup mode of the development board
Set the "BOOT MODE" DIP switch on the development board to the normal startup mode.
[Start Mode]: 1 (OFF), 2 (ON)
[Download Mode]: 1 (ON), 2 (OFF)
Note: ON of the DIP switch is on the letter side and OFF is on the number side.
#### Power on the development board
Press the "-" of the power switch "SWITCH" of the development board to turn on the power switch of the development board. At this time, you can see that the development board LED lights are partially on.
<br/>

### Interpretation of the startup information of the development board

-------------------------------------------------- ------------------------------
After the development board is powered on, you can see the startup information output by the development board on the serial terminal software.
<pre>
U-Boot 2016.092.0+ga06b20925c (Nov 01 2019 - 18:45:12 +0800)

SoC:  LS1012A Rev1.0 (0x87040110)
Clock Configuration:
       CPU0(A53):800  MHz  
       Bus:      250  MHz  DDR:      1000 MT/s
Reset Configuration Word (RCW):
       00000000: 08000008 00000000 00000000 00000000
       00000010: 33050000 c000000c 40000000 00001800
       00000020: 00000000 00000000 00000000 00004570
       00000030: 00000000 00c28120 00000096 00000000
I2C:   ready
DRAM:  510 MiB


......

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 4.1.35-rt41 (linyn@u12045) (gcc version 4.9.3 20150311 (prerelease) (Linaro GCC 4.9-2015.03) ) #1 SMP Mon Nov 4 19:59:14 CST 2019
[    0.000000] CPU: AArch64 Processor [410fd034] revision 4

......

Starting system log daemon...0
Starting kernel log daemon...0
Starting internet superserver: xinetd.

QorIQ SDK (FSL Reference Distro) 2.0 ls1012a-ek200 /dev/ttyS0
</pre>
#### U-Boot Information
The "U-Boot 2016.092.0 + ga06b20925c (Nov 01 2019-18:45:12 +0800)" in the startup information contains the following information:
[U-boot version]: 2016.09;
[Version number of source code]: ga06b20925c;
[Compile time of u-boot file]: Nov 01 2019-18:45:12 +0800.
#### Kernel information
"Linux version 4.1.35-rt41 (linyn @ u12045) (gcc version 4.9.3 20150311 (prerelease) (Linaro GCC 4.9-2015.03))" # 1 SMP Mon Nov 4 19:59:14 CST 2019 "in the startup information contains the following Information:
内核 [Kernel Version]: Linux-4.1.35;
[Kernel source version number]: rt41;
[GCC version of the compiled kernel]: 4.9.3;
[Compile time of the kernel file]: Mon Nov 4 19:59:14 CST 2019.
<br/>

### Development Board Login

-------------------------------------------------- ------------------------------
When you output "ls1012a-ek200 login:" after starting the system, you can log in:
[User name]: root
[Password]: None
Note: After logging in, you can set and modify the password through the "passwd" command.
<br/>
--------------------------------------------------------------------------------
<pre>
--------------------------------------------------------------------------------
* 珠海明远智睿科技有限公司  
* ZhuHai MYZR Technology CO.,LTD.
* Latest Update: 2019/11/14  
* Supporter: Tang Bin
--------------------------------------------------------------------------------
</pre>