查看“MYZR-IMX6-MB200 Hardware Introduction”的源代码

<div>

= '''overview of interfaces''' =
----
== '''Front view''' ==
[[File:myimx6ek200_front_.jpg|647px]]

== '''Rear view''' ==
[[File:myimx6ek200_rear view.jpg|642px]]

= '''Interface function''' =
----
== '''18/24bit LVDS0''' ==
:Silk screen：J24<br>
:LVDS0 crystal liquid is 24 bit mode，compatible with 18bit mode，through which LVDS resistance screen panel and LVDS capacitor screen panel in different sizes and specifications produced by MYZR can be cnnected。LVDS0 interface block is build with connector imported，abandon the cheap drawer type produced domestically，which is opposite press type to ensure easier installation,better performance and connectivity.<br>
:Definition of pin & signal as below<br>
[[File:myimx6_mb200_2.1.0.1.png]]
{| class="wikitable"
|-
!Pin	
!Singnal	
!Description
|-
|J24-16	
|SD1_DAT1/TOUCH_nEINT1	
|GPIO control
|-
|J24-17	
|NANDF_CS3	
|GPIO control
|-
|J24-19	
|DISP0_CONTRAST	
|LVDS0 backlight adjustment
|-
|J24-21	
|TOUCH_SCL	
|I2C clock
|-
|J24-22	
|TOUCH_SDA	
|I2C data
|}

== '''18/24bit RGB''' ==
:Silkscreen:J23<br>
:RGB crystal liquid is 24bit mode，compatible to 18bit/16bit mode,through which RGB resistance screen panel and RGB capacitor screen panel in different sizes and specifications produced by MYZR can be cnnected，RGB interface block is build with connector imported，abandon the cheap drawer type produced domestically，which is opposite press type to ensure easier installation,better performance and connectivity。</span><br>
:Definition of pin & signal：<br>
[[File:myimx6_mb200_2.2.0.1.png]]
{| class="wikitable"
|-
!Pin	
!Singnal	
!Description
|-
|J23-31	
|SD1_DAT1/TOUCH_nEINT1	
|GPIO control
|-
|J23-30	
|NANDF_CS3	
|GPIO control
|-
|J23-19	
|DISP0_CONTRAST	
|LVDS0 backlight adjustment
|-
|J23-32	
|TOUCH_SCL	
|I2C clock
|-
|J23-33	
|TOUCH_SDA	
|I2C data
|}


== '''18/24bit LVDS1''' ==
:Silk screen：J22<br>
:LVDS1 crystal liquid interface is the same as LVDS0 in terms of definition and connector model，users can connect crytal liquid in LVDS0 directly to LVDS1.<br>
:Definition of pin & signal：<br>
[[File:myimx6_mb200_2.3.0.1.png]]
{| class="wikitable"
|-
!Pin	
!Singnal	
!Description
|-
|J22-16	
|SD1_DAT1/TOUCH_nEINT1	
|GPIO control
|-
|J22-17	
|NANDF_CS3	
|GPIO control
|-
|J22-19	
|DISP0_CONTRAST	
|LVDS0 backlight adjustment
|-
|J22-21	
|TOUCH_SCL	
|I2C clock
|-
|J22-22	
|TOUCH_SDA	
|I2C data
|}

== '''10M/100M Ethernet-1''' ==
Silk screen：P4<br>
Interface property：100 - Mbps Ethernet standard interface<br>


== '''Earphone output''' ==
Silk screen：J20<br>
Interface property：audio signal output，3.5mm interface <br>


== '''Microphone input''' ==
Silk screen：J18<br>
Interface propoerty：audio signal input，3.5mm interface<br>

== '''HDMI''' ==
Silk screen：J5<br>
Interface property：HDMI-1.4 standard interface<br>

== '''SATA power supply''' ==
silk screen：J12<br>
Definition of pin & signal：<br>
{| class="wikitable"
|-
!pin	
!signal
!description
|-
|J12-1	
|5VIN	
|5V power input
|-
|J12-2	
|GND	
|digital
|-
|J12-3	
|GND	
|digital
|-
|J12-4	
|NC	
|unconnected
|}

== '''OTG''' ==
silk screen：J5<br>
Interface property：USB ON-The-GO，for burn and write<br>

== '''SATA II''' ==
Silk screen：J11<br>
Interface property：3Gbps SATA II standard interface <br>

== '''10M/100M Ethernet-2''' ==
Silk screen：P3<br>
Interface property：100 - Mbps Ethernet standard interface<br>

== '''USB expansion''' ==
silk screen:J8<br>
Interface property：USB1 expanded to dual USB，standard USB interface<br>


== '''Debug uart ''' ==
Silk screen：P2<br>
Interface property：3 thread standard RS232 port，for debug of sirial port <br>
[[File:myimx6_mb200_2.13.0.1.png|642px]]

== '''Main power supply switch''' ==
Silk screen：J3<br>
Interface property：power supply switch  <br>
Status property：—，close；O，off <br>

== '''Main power supply switch''' ==
Silk screen：J4<br>
Interface property：<br>
::Jack with inside positive and outside negative <br>
::Voltage：5V<br>
::Current：2.5A and above <br>

== '''Reset''' ==
Silk screen：SW1<br>
Function：reset <br>

== '''Wake up''' ==
Silk screen：SW2<br>
Interface property：sleeping wake up <br>

== '''Volume up''' ==
Silk screen：SW3<br>
Interface property：volume control（volume up）<br>


== '''Volume down''' ==
Silk screen：SW2<br>
Interface property：volume control（volume down）<br>


== '''RS-232 serial port''' ==
silk screen：P1<br>
Interface property：UART4，3 thread standard RS232 port <br>
[[File:myimx6_mb200_2.20.0.1.png|642px]]
 
 
== '''RS-485 serial port''' ==
Silk screen：J2<br>
Interface property：UART3，RS-485 serial port<br>
[[File:myimx6_mb200_2.21.0.1.png|642px]]

== '''MINI-PCIE''' ==
Silk screen：J6<br>
Interface property：standard MINI-PCIE port<br>


== '''Serial port expansion/TTL electrical level''' ==
Silk screen：J1<br>
[[File:myimx6_mb200_2.23.0.1.png|642px]]


== '''GPIO/SD2''' ==
Silk screen：J4<br>
[[File:myimx6_mb200_2.24.0.1.png|642px]]


== '''SPI expansion''' ==
Silk screen：J7<br>
[[File:myimx6_mb200_2.25.0.1.png|642px]]


== '''SIM cassette''' ==
Silk screen：CON1<br>
Interface property：standard SIM cassette<br>


== '''MIPI-CSI''' ==
Silk screen:J9<br>
[[File:myimx6_mb200_2.27.0.1.png]]


== '''CMOS-CSI''' ==
Silk screen:J14<br>
[[File:myimx6_mb200_2.28.0.1.png|642px]]


== '''CAN2''' ==
Silk screen:J16<br>
Interface property：CAN2<br>
[[File:myimx6_mb200_2.29.0.1.png]]


== '''CAN1''' ==
Silk screen:J19<br>
Interface property：CAN1<br>
[[File:myimx6_mb200_2.30.0.1.png]]


== '''I2C expansion''' ==
Silk screen:J21<br>
[[File:myimx6_mb200_2.31.0.1.png|642px]]


== '''GPS antenna pedestal''' ==
Silk screen:E4<br>
Interface property：antenna pedestal<br>

== '''GPS''' ==
Silk screen:U15<br>
Module model：NEO-6M<br>


== '''MINI_PCIE_FPC''' ==
Silk screen:J26<br>
Note：can't be used with MINI_PCIE simultaneously，e.g can only choose one from the two.<br>
[[File:myimx6_mb200_2.34.0.1.png]]


== '''SD3''' ==
Silk screen:J25<br>
Interface property：standard SD cassette <br>
[[File:myimx6_mb200_2.35.0.1.png|642px]]

== '''WIFI''' ==
Silk screen:U16<br>
Module model：UM12BS<br>
[[File:myimx6_mb200_2.36.0.1.png|642px]]

== '''RTC''' ==
Silk screen:U19<br>
Interface property：real clock for I2C communication <br>
[[File:myimx6_mb200_2.37.0.1.png|642px]]

== '''RTC_Batter''' ==
Silk screen:BT1<br>

</div>