2020年10月22日 (四) 05:50 Admin

2020-10-22T05:50:36Z

Admin：Admin移动页面MY-IMX6-EK200 Android-5.1.1 Test Manual至MYZR-IMX6-EK200 Android-5.1.1 Test Manual，不留重定向

2020-10-22T05:45:02Z

Admin移动页面MY-IMX6-EK200 Android-5.1.1 Test Manual至MYZR-IMX6-EK200 Android-5.1.1 Test Manual，不留重定向

2019年1月8日 (二) 06:34 Admin

2019-01-08T06:34:44Z

显示更改

Admin：创建页面，内容为“
= '''Applicable scope''' = 640px
= '''Test project''' = == '''UART test''' == === '''Test instruction''' === （1）Total...”

2018-07-23T09:16:06Z

创建页面，内容为“<div> = '''Applicable scope''' = 640px = '''Test project''' = == '''UART test''' == === '''Test instruction''' === （1）Total...”

新页面

<div>

= '''Applicable scope''' =

[[File:Android test 1.jpg|640px]] 

= '''Test project''' =
== '''UART test''' ==
=== '''Test instruction''' ===

（1）Total 4 serial interfaces,defaulted Uart2 by test program,but you can choose other interface as per what is needed. 
（2）Need to shorten send&receive pins of interface before test,pins shortened are different among different development boards,correspondence as below : 
[[File:Android test 2.1.1.jpg|640px]] 

（3）Here choose defaulted configuration,i.e Uart2，shorten the according pins. 

=== '''Test method''' ===

（1）Click“Uart”button，to boot test program. 

[[File:Android test 2.1.2.jpg|640px]] 

（2）Click“OpenDev”to open device. 
（3）Click“send”to send data. 
If there is a successful receiving of data,texbox will be popuped on the right side,i.e.a success of test,as below: 
[[File:Android test 2.1.2 2.jpg|640px]] 
If not receiving of data,that means a failure of test, please check out whether pins were shortened, errors as below: 

[[File:Android test 2.1.2 3.jpg|640px]] 

（5）When test is finished,click close,to exit the test of serial interface. 

== '''SPI test''' ==
=== '''Test instruction''' ===
（1）Need to shorten SPI pins before test,pins shortened are different among different development boards,correspondence as below: 

[[File:Android test 2.2.1.jpg|640px]] 

（2）EK200 match up with test program by SPI2；EK314 match up with test program by SPI1；so need to shorten pins according to actual condition. 
=== '''2.2.2 Test method''' ===
（1）Click“SPI”button，to boot test program. 

[[File:Android test 2.2.2.jpg|640px]] 

（2）Click“OpenDev”to open device. 
（3）Click“send”to send data。if there is a successful receiving of data,texbox will be popuped on the right side,i.e.a success of test,as below: 

[[File:Android test 2.2.2 2.jpg|640px]] 

If not receiving of data,that means a failure of test, please check out whether pins were shortened, errors as below: 

[[File:Android test 2.2.2 3.jpg|640px]] 

（4）When test is finished,click close,to exit the test program. 

== '''I2C test''' ==

=== '''Test instruction''' ===

There are total 3 IIC bus on evaluation board,each bus has its own device,test program only list the device for each bus,not for test. 

=== '''Test method''' ===

（1）Click“I2C”button，to boot test program. 

[[File:Android test 2.3.2.jpg|640px]] 

（2）Click“ListI2C”，to list all I2C bus，total 3 units，the following figure: 

[[File:Android test 2.3.2 2.jpg|640px]] 

（3）Click“ListDevice”to list all devices on one of the bus，default is i2c-0,as below: 

[[File:Android test 2.2.2 3.jpg|640px]] 

（4）Click drop-down manu on right，to get separate list of devices on the other two bus，example: 

[[File:Android test 2.2.2 4.jpg|640px]] 
[[File:Android test 2.2.2 5.jpg|640px]] 

（5）Finish test,exit test. 

== '''CAN test''' ==
=== '''Test instruciton''' ===

Need to connect CAN pins before test，connect CAN_L of CAN1 with CAN_L of CAN2，connect CAN_H of CAN1 with CAN_H CAN2. 

=== '''Test method''' ===

（1）Click“CAN”button，to boot test program 

[[File:Android test 2.4.2 .jpg|640px]] 

（2）Click“OpenDev”to open device，click“Send”to send data，if there is a successful receiving of data,texbox will be popuped on the right side，as below: 

[[File:Android test 2.4.2 2.jpg|640px]] 

If not receiving of data,that means a failure of test, please check out whether CAN pins were shortened，errors as below: 

[[File:Android test 2.4.2 3.jpg|640px]] 

（3）Test is over，exit CAN test. 

== '''USB&SD test''' ==
=== '''Test instruction''' ===
（1）Check out whether USB and SD read & write is normal or not. 
=== '''Test method''' ===
（1）Click“SD/U disk”button，to boot test program. 

[[File:Android test 2.4.5.jpg|640px]] 

（2）Insert U disk or SD card，click“SD”or“U disk”button to read out the content of SD card or U disk. 

[[File:Android test 2.4.5 2.jpg|640px]] 

（3）Test is over，exit test program 

== '''WIFI& lan port test''' ==

=== '''Test instruction''' ===

Check out function of WIFI and lan port. 

=== '''WIFI test method''' ===

（1）Click“WIFI button”，to boot test program. 

[[File:Android test 2.6.2.jpg|640px]] 

（2）Click“wifi”switch，after open wifi then click“search”to search wifi. 

[[File:Android test 2.6.2 2.jpg|640px]] 

（3）Click Wifi which will be linked，enter password for the link. 

（4）If a successful link,then click“Link”to link with baidu. 

（5）If failure of link,please check out whether network is working. 

=== '''Lan port test method''' ===

（1）Connect lan cable with lan port 

（2）Click“Intent”button to link to baidu 

== '''Multi media test''' ==

=== '''Test instruction''' ===

（1）Test functions of audio and vedio.

=== '''Test method''' ===

（1）Click“Audio/video”button，to boot test program. 

[[File:Android test 2.7.2.jpg|640px]] 

（2）Wear earphone,click“Play_music”，can hear a piece of music. 

（3）Click“Play_video”，to play a piece of vedio. 

[[File:Android test 2.7.2 2.jpg|640px]] 

（4）Test is over，exit test program. 

== '''GPIO test''' ==

=== '''Test instruction''' ===

（1）Test functions of GPIO.

=== '''Test method''' ===

（1）Click and select the GPIO port to test in the output1 or output2 drop-down box. 

[[File:Android test 2.7.2 3.png|640px]] 

（2）Click the button named“output1“ to control the level of the left port, and click the button named "output2" can control the level of the right port. 

（3）Click the "1" in the left side can make "output1" be high level, click the 0 in the left side can make "output1" be low level. You also can click on the right side of the figure to control the level of "output2" as well. 

== '''Product instroduction''' ==

=== '''Product photo''' ===

（1）Click“Product”button，you can see the instruduction and photo of our products,left or right sliding screen for more information. 

[[File:Android test 2.8.1.png|640px]] 

</div>

@@ 第2行： / 第2行： @@
 ## **Applicable scope**
-[[File:Android test 1.jpg|640px]]
 ## **Test project**
 ### I.）uart Test
@@ 第26行： / 第45行： @@
 ###**Iii.）Spi Test**
 Before the test, the pins of the SPI need to be short-connected. The pins of the short connections of different development boards are different. The corresponding relationships are as follows:
-[[File:Android test 1.4.jpg|640px]]
 * Test method:

←上一版本	2020年10月22日 (四) 05:45的版本
（没有差异）

MYZR-IMX6-EK200 Android-5.1.1 Test Manual - 版本历史

2020年10月22日 (四) 05:50 Admin

Admin：Admin移动页面MY-IMX6-EK200 Android-5.1.1 Test Manual至MYZR-IMX6-EK200 Android-5.1.1 Test Manual，不留重定向

2019年1月8日 (二) 06:34 Admin

Admin：创建页面，内容为“ = '''Applicable scope''' = 640px = '''Test project''' = == '''UART test''' == === '''Test instruction''' === （1）Total...”

Admin：创建页面，内容为“
= '''Applicable scope''' = 640px
= '''Test project''' = == '''UART test''' == === '''Test instruction''' === （1）Total...”