MYZR-IMX6-EK200 Linux-3.0.35 Test Manual - 版本历史

Admin：Admin移动页面MY-IMX6-EK200 Linux-3.0.35 Test Manual至MYZR-IMX6-EK200 Linux-3.0.35 Test Manual，不留重定向

2020-10-22T05:43:30Z

Admin移动页面MY-IMX6-EK200 Linux-3.0.35 Test Manual至MYZR-IMX6-EK200 Linux-3.0.35 Test Manual，不留重定向

2020年10月22日 (四) 05:43 Admin

2020-10-22T05:43:21Z

Admin：/* Reveal function test */

2018-11-08T07:38:31Z

‎Reveal function test

Admin：/* Reveal function test */

2018-11-08T07:28:43Z

‎Reveal function test

2018年7月23日 (一) 09:06 Admin

2018-07-23T09:06:42Z

Admin：创建页面，内容为“
= '''Preparation before test''' = ---- :1）Please refer to "connection of device"->"Linux fast boot" in 《Linux fast boot manual》 for the connection.br>...”

2018-07-23T09:01:25Z

创建页面，内容为“<div> = '''Preparation before test''' = ---- :1）Please refer to "connection of device"->"Linux fast boot" in 《Linux fast boot manual》 for the connection.br>...”

新页面

<div>

= '''Preparation before test''' =
----
:1）Please refer to "connection of device"->"Linux fast boot" in 《Linux fast boot manual》 for the connection.br>
:2）Please refer to "booting device" ->"Linux fast boot" in 《Linux fast boot manual》 for the booting. 

= '''Test item''' =
----
== '''Lan port test''' ==
MY-I.MX6 evalution board support dual lan port（two 100-Mbps ethernet lan ports2）. 

=== Test instruction ===
The first ethernet lan port is “P4”on front view of base board，the second one is “P5”on front view of base board. 
Defauted lan port is the first one after system boot,with defauted IP as 192.168.3.104. 

=== Test method ===
Test the first ethernet lan port 
Connect lan line：connect “P4”on evaluation board with computer lan port through network 
Set computer IP：set computer lan port IP as 192.168.3.9 
[[File::MY-IMX6-EK200 L3035_2.1.2.1.png]] 
*Run test command ：$ ping -I eth0 192.168.3.9 -c 2 -w 4 
Observe test result：system will output following information： 
--- 192.168.3.9 ping statistics --- 
2packets transmitted, 2 packets received, 0% packet loss

*Test result：“0% packet loss”represent test passing. 

2）Test the second ethernet lan port. 
* Connect lan line：take out lan line from the first lan port then plug in “P5”on evaluation board，another end of lan line is kept in connection with lan port of computer. 
* Set computer IP：set computer lan port IP as 192.168.3.9（if the setting was already done then go direclty into next step）. 
* Set the second lan port IP：$ ifconfig eth1 192.168.3.18，after the setting system will output working condition of the second lan port, as below： 
smsc95xx 2-1.1:1.0: eth1: link up, 100Mbps, full-duplex, lpa 0xCDE1 
* Run test command：$ ping -I eth1 192.168.3.9 -c 2 -w 4 
* Observe test result：system will output the following message. 
--- 192.168.3.9 ping statistics --- 

2packets transmitted, 2 packets received, 0% packet loss 
* Test result：“0% packet loss”represent test passing. 

=== reference symbols ===
Instruction： 
　　The first red frame is test command for lan port 1. 
　　The second red frame is test result for lan port1. 
　　The third red frame is IP configuration for lan port2. 
　　The fourth red frame is status information for lan port2. 
　　The fifth red frame is test command for lan port2. 

[[File::MY-IMX6-EK200 L3035_2.1.3.1.png]] 

== '''USB test''' ==
=== Test Instruction ===
　　MY-I.MX6 V2.5 evaluation board has two USB HOST ports，in“J8”in base board. 

=== Test method ===
　　1） Start test 
　　Plug USB device in USB port in base board，system will output the following message： 
usb *-*.*: new high speed USB device number * using fsl-ehci 
…… 
　　2） Test end 
　　Take out USB device from the base board，system will output the following message： 
usb *-*.*: USB disconnect, device number * 

=== reference symbols ===
Instruction：. 
　　The first red frame in image is message outputed by system when insert U disk. 
　　The second red frame in image is message outputed by system when take out U disk. 
　　The third red frame in image is message outputed by system when insert USB mouse. 
　　The fourth red frame in image is message outputed by system when take out USB mouse. 
[[File::MY-IMX6-EK200 L3035_2.2.3.1.png]] 

== '''SD card interface test''' ==
=== Test instruction ===
　　SD card interface is in“J25”in rear view of base board. 

=== Start test ===
　　1）Insert device in SD card slot. 
　　Insert SD card in SD card port in base board, system will output following message(see attached image),e.g.SD port is normal： 
mmc*: new high speed SD card at address **** 
mmcblk*: mmcx:xxxx SA**G *.**GiB 
mmcblk*: p* 

　　2）Pop-up device from SD card slot. 
　　Press again SD card in SD card slot，base board will pop-up SD cardsystem will output following message(see attached image),e.g.function of SD card port pop-up is normal： 
mmc*: card **** removed 

　　3） End test 
　　Take out SD card after SD card pop-up,to end the test. 

=== reference symbols ===
[[File::MY-IMX6-EK200 L3035_2.3.3.1.png]] 
== '''A/V test''' ==
=== Test instruction ===
:This test is to verify the function of video & audio of evaluation board by playing vocal video. 

=== Test method ===
:1）Prepare test 
:Connect audio output device to audio element in front view of base board,audio element is “J20”in front view of base board，silkscreened as“HP”. 

:2）Execute test 
:Play a video with gplay，commanded as below： 
$ gplay /app_test/arm.flv 
:The above command will play a file designated by command with gplay. 
:3）Test result 
:You can see the vedeo played on display screen of evaluation board and hear the voices outputed by audio device. 

=== reference symbols ===
[[File::MY-IMX6-EK200 L3035_2.4.3.1.png]] 
== '''LED（GPIO）test''' ==
=== Test instruction ===
:CPU pin used in LED（GPIO）test is“NANDF_CS0” ，connect to “no.4 pin of J4 ”，GPIO will be controled by test programs to output high and low ectrical level after running test program,interval between high and low electrical level is 1 second. 
:Tip: LED (GPIO) testing requires a multimeter, and users without a multimeter can skip the next test.

=== Test method ===
　　1）Execute test program 
　　Enter command in terminal to run the test program，example as below： 
　　$ /app_test/led 
　　At this hour GPIO will be controled by test programs to output high and low ectrical level,and output message similar to below. 
Write=0 
Write=1 
…… 

　　2）Check test result. 
　　Connect ground of multimeter with ground of development board，another line of multimeter is connected to no.4 pin of J4，voltage of multimeter will jump. 
　　3）End test 
　　Press“Ctrl”+“C”on computer,to end the key test program. 

=== reference symbols ===
[[File::MY-IMX6-EK200 L3035_2.5.3.1.png]] 
== '''Key test''' ==
=== Test instruction ===
　　There are 4 keys on MY-I.MX6 base board，three of them are custom function keys(SW2：WAKE UP，SW3:V+，SW4:V-），and one reset key（SW1：nRE）test program key_test can test these 3 function keys. 

=== Test method ===
　　1）Execute test program. 
　　Press command in terminalto run test program，example as below： 
　　$ /app_test/key_test 

　　2）Proceed with interactive test. 
　　Press separately SW4、SW3、SW2，system will output corresponding message as below： 
key*** Pressed 
key*** Released 
　　Message of“key*** Pressed”is outputed with press of key，message of“key*** Released”is outputed with release of key. 
　　3）End test 
　　Press “Ctrl”+“C”on computer to send the test program for keys. 
Note：press SW1（system will reset and reboot）. 

=== reference symbols ===
[[File::MY-IMX6-EK200 L3035_2.6.3.1.png]] 
== '''Serial port test''' ==
:There are 5 serial ports in MY-I.MX6 evaluation board，4 are user serial ports（in “J1”in front view of base board，silkscreened as“TTL_UART”），one is debug serial port（in “P2”in front view of base board）. 

=== Test instruction ===
:Instruction of system device file： 
* Device file for debug serial port in the system is ttymxc0，device file for user serial port are ttymxc1、ttymxc2、ttymxc3、ttymxc4. 
:Instruction for transceiver pin of serial ports and their corresponding device file： 
* UART2：send 7，receive 9，ttymxc1 
* UART3：send 11，receive 13，ttymxc2 
* UART4：send 17，receive 15，ttymxc3 
* UART5：send 18，receive 16，ttymxc4 
Tips：transceiver pins of serial port are listed here,but please refer to schematic for definition of all pins of serial port. 

=== Test method ===
　　Adopt method of self-sending & self-receiving of serial port. 
　　Tips：here take serial port 5 as example,please refer to serial port test method for the test of the other 3 user serial ports. 

　　1）Prepare test 
　　Short connect sending pin and receiving pin of serial port 5（no.16 and no.18 pin of J1）. 

　　2）Execute test. 
　　$ ~/my-demo/linux-3.0.35/uart_test.out /dev/ttymxc4 "www.myzr.com.cn" 

　　3）Test result. 
　　If serial port is normal,terminal will reveal similar message as below： 
Read Test Data finished,Read Test Data is-------www.myzr.com.cn 

=== reference symbols ===
[[File::MY-IMX6-EK200 L3035_2.7.3.1.png]] 
== '''RTC test''' ==
=== Test instruction ===
　　Due to restrictions in transportation，MY-I.MX6 evaluation board doesn't contatin battery in deliverybefore RTC test please prepare button cell to install on “BT1”in rear view of base board（beside silkscreened name of“RTC”）. 

=== Test method ===
　　Power off then reboot device,to check the time of system and hardware. 
　　Command to check clock of current system as below： 
$ date 
　　Message outputed by system as below： 
Thu Jan 1 00:00:59 UTC 1970 
　　Command to check clock of RTC chip as below： 
$ hwclock 
　　Message outputed by system as below： 
Tue Nov 30 00:00:00 1999 0.000000 seconds 
　　2）Set system clock and synchronously set to RTC chip. 
　　Command to set system clock are with below reference： 
$ date -s "2015-04-27 12:34:56" 
　　Command to write system clock into hardware as below： 
$ hwclock –w 
　　3）Power off and reboot evaluation board，to check current system clock and hardware clock. 
　　Please refer to step 1. 
　　4）Test result. 
　　It will be a newly-set clock after execution until step 3. 
=== reference symbols ===
Below image is screenshots for step1 and step 2 in the test. 
[[File::MY-IMX6-EK200 L3035_2.8.3.1.png]] 
Below image is the screenshots for step3 in the test. 
[[File::MY-IMX6-EK200 L3035_2.8.3.2.png]] 

== '''WatchDog test''' ==
=== Test instruction ===
　　WatchDog test includes two items：one is reset test，the other is feed dog test. 

=== Reset test ===
　　1）Test instruction 
　　Reset test will boot WatchDog，but doesn't feed dog，system will reset after 60 seconds. 

　　2） Execution test 
　　Run /app_test/watdogrestart，instanced command as below： 
$ /app_test/watdogrestart 
　　3）Test result 
　　Wait for 60 seconds after running of test command，WatchDog timeout，system is resettedyou can see message outputed by system rebooting on terminal. 

=== Dog feeding test ===
　　1）Test instruction 
　　Feeding dog test will boot WatchDog，and feed dog once a second，system won't reset because of WatchDog timeout. 

　　2）Execute test 
　　Run /app_test/watdogtest &，instanced example as below：. 
$ /app_test/watdogtest & 

　　3）Test result 
　　After run the test command,system still works normally and won't reset because of WatchDog timeout. 

　　4）figure 
[[File::MY-IMX6-EK200 L3035_2.9.3.1.png]] 

== '''SPI test''' ==
　　There are a group of SPI ports on MY-I.MX6 V2.5 base board，located on“J7”，silkscreened as “SPI”. 

=== Test instruction ===
　　MISO pin and MOSI pin of SPI port will be used for the testSMISO pin of SPI port is “no.8 of J7”on the base board，and MOSI pin is “no.10 of J7”. 

=== Test method ===
:Adopt way of SPI self-sending（output）self-receiving（input). 

:1）Prepare test 
:Short connect MISO pin and MISO pin of SPI port，e.g.short connect pin no.8 and pin no.10 of J7 on the base board. 

:2）Execute test 
:$ ~/my-demo/linux-3.0.35/spidev_test.out -D /dev/spidev1.0 

:3）Test result 
:If SPI is normal，you can see on terminal the following charaters： 
FF FF FF FF FF FF 
40 00 00 00 00 95 
FF FF FF FF FF FF 
FF FF FF FF FF FF 
FF FF FF FF FF FF 
DE AD BE EF BA AD 
F0 0D 

=== Figured ===
[[File::MY-IMX6-EK200 L3035_2.10.3.1.png]] 
== '''CAN interface test''' ==
=== Test instruction ===
　　Oscilloscope will be used for CAN test，please skip this step for users who don't have oscilloscope. 
=== Test method ===
　　1）Configuration CAN0. 
　　Instanced example as below： 
$ ip link set can0 up type can bitrate 250000 

　　2）Configuration of link for oscilloscope 
Connect CH1 and CH2 with “R83”of evaluation board（the green stand on topside on front view of base board）. 
Configure oscilloscope（for users who don't know how to use oscilloscope ,please ask hardware engineers for assistance ）. 
　　3）Execute test command. 
$ /app_test/client_test 
　　4）Rest result. 
　　When exectue the test command,you can see a waving change on oscilloscope. 

=== Figured ===
[[File::MY-IMX6-EK200 L3035_2.11.3.1.png]] 
== '''PCIE interface test''' ==
=== Test instruction ===
　　System is already added with drivers for PCI port，in booting system will check out devices on PCI-E interface. 

=== Test method ===
　　Reset system，observe the message outputed by system booting. 
　　1）PCI-E driving program output messages. 
　　In the course of system booting, if there is outputed message as below,e.g PCI-E interface load is normal： 
iMX6 PCIe PCIe RC mode imx_pcie_pltfm_probe entering. 
PCIE: imx_pcie_pltfm_probe start link up. 

　　2）Message outputed without link of PCI-E device. 
　　In the course of system booting，it there is not a valid device linked with PCI-E interface，system will prompt“link down!”on PCI-E port，something as below： 
link up failed, DB_R0:0x00361900, DB_R1:0x08200000! 
IMX PCIe port: link down! 

　　3）Message outputed when there is a valid PCI-E device linked（here take Intel 4965AGN as an example） 
　　In the course of system booting，if PCI-E port detect a valid device and the device module is normal，system will prompt“link up”on PCI-E port，as below： 
IMX PCIe port: link up. 

　　4）Linux test command：$ lspci. 
　　If a valid PCI-E device is inserted on PCI-E port,information related to the module will be gained with lspci，something like this（what is linked is Intel 4965AGN in this case）： 
00:00.0 Class 0604: 16c3:abcd 
01:00.0 Class 0280: 8086:4229 
　　If there is not device linked with PCI-E port，lspci system won't output any message. 

===figured ===
Following figure is message outputed by system without a link with PCI-E device. 
[[File::MY-IMX6-EK200 L3035_2.12.3.1.png]] 
 
The following figure is message ouputed by system with a link to Intel 4965AGN. 
[[File::MY-IMX6-EK200 L3035_2.12.3.2.png]] 
 
Following figure is message by use of lspci after entering system on the condition of a link with Intel 4965AGN. 
[[File::MY-IMX6-EK200 L3035_2.12.3.3.png]] 

== '''WIFI test''' ==
=== Test instruction ===
　　Model no. of WIFI chip ussed for MY-I.MX6 evaluation board is RTL8188EUS. 
=== Test method ===
　　1）Load WIFI module driver 
　　Instanced command as below： 
$ insmod /lib/modules/wifi/wlan.ko 

　　2）Generate WIFI config file. 
　　Refered command as below： 
$ wpa_passphrase MYZR_TP-LINK myzrd2302 > /etc/wpa_supplicant.conf 
　　Both name and password of WIFI designated by this command are “MYZR_TP-LINK myzrd2302”，need to replace with your own linkable WIFI name and password. 

　　3）Link WIFI network. 
　　Instanced command as below：. 
$ wpa_supplicant -B –c /etc/wpa_supplicant.conf -iwlan0 

4）Automaically gain IP. 
　　Instanced command as below： 
$ udhcpc -i wlan0 
　　Note：need to ensure a DHCP function opened for WIFI network in use. 
　　5）Test WIFI network link. 
　　Instanced command as below： 
$ ping -I wlan0 www.baidu.com -c 2 
　　6）Test result 
　　Execute step 5 if ok, e.g. WIFI module is normal to work. 

=== Figured ===
[[File::MY-IMX6-EK200 L3035_2.13.3.1.png]] 
 
[[File::MY-IMX6-EK200 L3035_2.13.3.2.png]] 

== '''IPU test''' ==
===Test instruction ===
The whole IPU test will take over ten minutes . 

=== Test method ===
　　1）Execute test 
　　Enter directory where test program is located（must enter directory where test program is locased for a normal test script）. 
$ cd /unit_tests/ 
　　Execute test script 
$ ./autorun-ipu.sh 
　　2）Test result 
　　In the whole test process，you can see a constant change of content on the display screen. 
　　After test is over，you can see on terminal the following message： 
test stop at Thu Jan 1 00:33:38 UTC 1970 

=== figured ===
[[File::MY-IMX6-EK200 L3035_2.14.3.1.png]] 
 
[[File::MY-IMX6-EK200 L3035_2.14.3.2.png]] 

== '''GPU test''' ==
=== Test instruction ===
　　Please follow /unit_tests/gpu.sh file for the details of test. 

=== Test method ===
　　1）Execute test 
　　Enter directory where test program is located（must enter directory where test program is locased for a normal test script）. 
$ cd /unit_tests/ 
　　* Execute test script. 
$ ./gpu.sh 
　　2）Test process. 
　　In the whole test process，you can see a constant change of content on the display screen. 
　　3）Exit test. 
　　Terminal output“press ESC to escape...”，press ESC to exit test. 

=== Figured ===
[[File::MY-IMX6-EK200 L3035_2.15.3.1.png]] 
== '''VPU test''' ==

=== Test instruction ===
　　In the test,vedio file will be decoded with VPU and outputed to the display device. 
=== Test method ===
　　1）Execute test 
　　Enter directory where test program is located（must enter directory where test program is locased for a normal test script）. 
$ cd /unit_tests/ 
　　* Execute test script. 
$ ./autorun-vpu.sh 
　　2）Test process 
　　In the whole test process，you can see the vedio decoded by VPU on the display screen. 

=== 附图(figured) ===
[[File::MY-IMX6-EK200 L3035_2.16.3.1.png]] 

= '''Reveal function test''' =
----
　　Instruction：need to re-boot system to enter u-boot command line for each reveal function test，enter command and press Enter key. 
　　Example as below：. 
== '''Single screen display''' ==
　　Instruction：enter command and press Enter key，observe the displayed content on screen in the course of system booting，Linux Logo can be seen. 

=== LVDS1 ===
　　Insert ribbon cable for screen to LVDS1（in “J22”on front view of base board，silkscreened as“LVDS1”），boot system，enter u-boot command line，enter the following commands and press Enter key： 
　　setenv bootargs console=ttymxc0,115200 ip=none root=/dev/mmcblk0p1 rootwait video=mxcfb0:dev=ldb,LDB-1024X600,if=RGB666; mmc dev 2; mmc read 0x10800000 0x800 0x2000; bootm 

=== LVDS0 ===
　　Insert ribbon cable for screen to LVDS0（in“J24”on front view of base board，silkscreened as“LVDS0”）,run system to enter u-boot command line，enter the following commands and press Enter key： 
　　setenv bootargs console=ttymxc0,115200 ip=none root=/dev/mmcblk0p1 rootwait video=mxcfb0:dev=ldb,LDB-1024X600,if=RGB666 ldb=sin0; mmc dev 2; mmc read 0x10800000 0x800 0x2000; bootm 

=== HDMI ===
　　setenv bootargs console=ttymxc0,115200 ip=none root=/dev/mmcblk0p1 rootwait video=mxcfb0:dev=hdmi,1920x1080M@60,if=RGB24; mmc dev 2; mmc read 0x10800000 0x800 0x2000; bootm 
　　Tips：there is not reveal of Linux Logo on screen for HDMI display in bootingvedio can be played with gplay command after entering system，vedio transfered can be seen on display screen. 
　　Example for vedio playing command as below： 
　　$ gplay /unit_tests/akiyo.mp4 

=== RGB ===
　　Enter u-boot command line，enter the following commands and press Enter key： 
　　setenv bootargs console=ttymxc0,115200 ip=none root=/dev/mmcblk0p1 rootwait video=mxcfb0:dev=lcd,SEIKO-WVGA,if=RGB24; mmc dev 2; mmc read 0x10800000 0x800 0x2000; bootm 

== '''Dual screens synchronous display''' ==
　　Instruction：enter command and press Enter key，Linux Logo is displayed on the two screens in kernel booting，and other operations to screen is also displayed on the two screens. 

=== LVDS1+LVDS0 synchronous display ===
　　setenv bootargs console=ttymxc0,115200 ip=none root=/dev/mmcblk0p1 rootwait video=mxcfb0:dev=ldb,LDB-1024X600,if=RGB666 ldb=dul0 video=mxcfb1:dev=ldb,LDB-1024X600,if=RGB666; mmc dev 2; mmc read 0x10800000 0x800 0x2000; bootm 

== '''Dual screen asynchronous display''' ==
=== Test commands probably to be used ===
*Turn on backlight of main display screen. 
$ echo 0 > /sys/class/graphics/fb0/blank 
* Turn on backlight of the second display screen. 
$ echo 0 > /sys/class/graphics/fb2/blank 
* Play the designated vedio file to vedio device（here video17 is related to main screen）. 
$ gst-launch playbin2 uri=file:///unit_tests/akiyo.mp4 \ 
video-sink="mfw_v4lsink device=/dev/video17" 
* Play the designated vedio file to vedio device（here video18 is related to the second screen）. 
$ gst-launch playbin2 uri=file:///unit_tests/akiyo.mp4 \ 
video-sink="mfw_v4lsink device=/dev/video18" 

=== Instruction of test method ===
1）Enter u-boot command line and enter commands then press Enter key and wait until booting is over. 
Example as below： 
2）Execute command turn on backlight of corresponding display screen. 
Example as below: 
3）Execute vedio playing command to play the vedio to display screen. 
Example as below：. 
Instruction：in the mode of dual screen asynchronous display ，the backlight defaut of the second screen is closed after system boot，so need to execute step2）. 

=== LVDS1 as main screen ===
* LVDS1+LVDS0 dual screen asynchronous display. 
　　setenv bootargs console=ttymxc0,115200 ip=none root=/dev/mmcblk0p1 rootwait video=mxcfb0:dev=ldb,LDB-1024X600,if=RGB666 video=mxcfb1:dev=ldb,LDB-1024X600,if=RGB666; mmc dev 2; mmc read 0x10800000 0x800 0x2000; bootm 
* LVDS1+RGB dual screen asynchronous display. 
　　setenv bootargs console=ttymxc0,115200 ip=none root=/dev/mmcblk0p1 rootwait video=mxcfb0:dev=ldb,LDB-1024X600,if=RGB666 video=mxcfb1:dev=lcd, SEIKO-WVGA,if=RGB24; mmc dev 2; mmc read 0x10800000 0x800 0x2000; bootm 
* LVDS1+HDMI dual screen asynchronous display. 
　　setenv bootargs console=ttymxc0,115200 ip=none root=/dev/mmcblk0p1 rootwait video=mxcfb0:dev=ldb,LDB-1024X600,if=RGB666 video=mxcfb1:dev=hdmi,1920x1080M@60,if=RGB24; mmc dev 2; mmc read 0x10800000 0x800 0x2000; bootm 

=== LVDS0 as main screen ===
* LVDS0+LVDS1 dual screen asynchronous display： 
　　setenv bootargs console=ttymxc0,115200 ip=none root=/dev/mmcblk0p1 rootwait video=mxcfb0:dev=ldb,LDB-1024X600,if=RGB666 ldb=sep0 video=mxcfb1:dev=ldb,LDB-1024X600,if=RGB666; mmc dev 2; mmc read 0x10800000 0x800 0x2000; bootm 
* LVDS0+RGB dual screen asynchronous display. 
　　setenv bootargs console=ttymxc0,115200 ip=none root=/dev/mmcblk0p1 rootwait video=mxcfb0:dev=ldb,LDB-1024X600,if=RGB666 ldb=sin0 video=mxcfb1:dev=lcd,SEIKO-WVGA,if=RGB24; mmc dev 2; mmc read 0x10800000 0x800 0x2000; bootm 
* LVDS0+HDMI dual screen asynchronous display. 
　　setenv bootargs console=ttymxc0,115200 ip=none root=/dev/mmcblk0p1 rootwait video=mxcfb0:dev=ldb,LDB-1024X600,if=RGB666 ldb=sin0 video=mxcfb1:dev=hdmi,1920x1080M@60,if=RGB24; mmc dev 2; mmc read 0x10800000 0x800 0x2000; bootm 

=== RGB as main screen ===
* RGB+LVDS1 dual screen asynchronous display： 
　　setenv bootargs console=ttymxc0,115200 ip=none root=/dev/mmcblk0p1 rootwait video=mxcfb0:dev=lcd,SEIKO-WVGA,if=RGB24 video=mxcfb1:dev=ldb,LDB-1024X600,if=RGB666; mmc dev 2; mmc read 0x10800000 0x800 0x2000; bootm 
* RGB+LVDS0 dual screen asynchronous display： 
　　setenv bootargs console=ttymxc0,115200 ip=none root=/dev/mmcblk0p1 rootwait video=mxcfb0:dev=lcd,SEIKO-WVGA,if=RGB24 video=mxcfb1:dev=ldb,LDB-1024X600,if=RGB666 ldb=sin0; mmc dev 2; mmc read 0x10800000 0x800 0x2000; bootm 

=== HDMI as main screen ===
* HDMI+LVDS1 dual screen asynchronous display 
　　setenv bootargs console=ttymxc0,115200 ip=none root=/dev/mmcblk0p1 rootwait video=mxcfb0:dev=hdmi,1920x1080M@60,if=RGB24 video=mxcfb1:dev=ldb,LDB-1024X600,if=RGB666; mmc dev 2; mmc read 0x10800000 0x800 0x2000; bootm 
* HDMI+LVDS0 dual screen asynchronous display 
　　setenv bootargs console=ttymxc0,115200 ip=none root=/dev/mmcblk0p1 rootwait video=mxcfb0:dev=hdmi,1920x1080M@60,if=RGB24 video=mxcfb1:dev=ldb,LDB-1024X600,if=RGB666 ldb=sin0; mmc dev 2; mmc read 0x10800000 0x800 0x2000; bootm 

= '''Instruction about environment variables''' =
----
== Features of environment variables of MY-IMX6 series of development board ==
　　Environment variables of MY-IMX6 series of development board feature as below： 
　　1. medium leading kernel includes：eMMC、network（tftp） 
　　2. medium leading file system includes：eMMC、network（NFS） 
　　3. configuration for display device includes: LVDS0、LVDS1、HDMI、RGB，and different combinations of dual screens 
　　In this case,if environment variables combine the three features mentioned above ，there will be at least 60 bootcmd environment variables,so we conduct abstract separation and recombination for environment variables. 
　　Since bootargs environment variables include parameter such as console、video、ip、root ，so each kind of bootcmd rely a lot on bootargs ，plus a big difference among different kinds of bootcmd,it is no question that bootargs are not universial. 

== Bootcmd_xxx environment variables procedure ==
　　We abstract bootcmd and bootargs based on guided device，after abstraction bootcmd_xxx procedure like this： 
　　1. Re-build bootargs through bootargs_base，to ensure no conflict among bootargs； 
　　2. Parameters corresponding to guided device are added after bootargs through bootargs_xxx； 
　　As to “;”in bootcmd_xxx ,the following will be easily understood. 

== Correct way to set environment variables ==
　　As to the correct ways to set environment variables： 
　　Must be noted that setting to bootargs in normal condition is invalid，because bootargs_base will re-set bootargs. 
　　Need to write the setting of bootargs to the commands of bootargs_base . 
　　Bootargs_base contains only console and video，other parameters should be written to bootargs_mmc or bootcmd_tftp or bootargs_nfs . 

== Example for correct way of environment variables setting ==
　　If need to set “HDMI+LVDS1 dual screen asynchronous display”and reserve environment variables，then： 
　　1. setenv bootargs_base 'setenv bootargs console=ttymxc0,115200 video=mxcfb0:dev=hdmi,1920x1080M@60,if=RGB24 video=mxcfb1:dev=ldb,LDB-1024X600,if=RGB666' 
　　2. saveenv 
　　The above two commands are applied. 
</div>

@@ 第9行： / 第9行： @@
 ----
 == '''Lan port test''' ==
-MY-I.MX6 evalution board support dual lan port（two 100-Mbps ethernet lan ports2）.<br>
+MYZR-I.MX6 evalution board support dual lan port（two 100-Mbps ethernet lan ports2）.<br>
 ===  Test instruction ===
@@ 第52行： / 第52行： @@
 == '''USB test''' ==
 ===  Test Instruction ===
-　　MY-I.MX6 V2.5 evaluation board has two USB HOST ports，in“J8”in base board.<br>
+　　MYZR-I.MX6 V2.5 evaluation board has two USB HOST ports，in“J8”in base board.<br>
 === Test method ===
@@ 第136行： / 第136行： @@
 == '''Key test''' ==
 ===  Test instruction ===
-　　There are 4 keys on MY-I.MX6 base board，three of them are custom function keys(SW2：WAKE UP，SW3:V+，SW4:V-），and one reset key（SW1：nRE）test program key_test can test these 3 function keys.<br>
+　　There are 4 keys on MYZR-I.MX6 base board，three of them are custom function keys(SW2：WAKE UP，SW3:V+，SW4:V-），and one reset key（SW1：nRE）test program key_test can test these 3 function keys.<br>
@@ 第157行： / 第157行： @@
 [[File:MY-IMX6-EK200 L3035_2.6.3.1.png]]<br>
 == '''Serial port test''' ==
-:There are 5 serial ports in MY-I.MX6 evaluation board，4 are user serial ports（in “J1”in front view of base board，silkscreened as“TTL_UART”），one is debug serial port（in “P2”in front view of base board）.<br>
+:There are 5 serial ports in MYZR-I.MX6 evaluation board，4 are user serial ports（in “J1”in front view of base board，silkscreened as“TTL_UART”），one is debug serial port（in “P2”in front view of base board）.<br>
@@ 第190行： / 第190行： @@
 == '''RTC test''' ==
 === Test instruction ===
-　　Due to restrictions in transportation，MY-I.MX6 evaluation board doesn't contatin battery in deliverybefore RTC test please prepare button cell to install on “BT1”in rear view of base board（beside silkscreened name of“RTC”）.<br>
+　　Due to restrictions in transportation，MYZR-I.MX6 evaluation board doesn't contatin battery in deliverybefore RTC test please prepare button cell to install on “BT1”in rear view of base board（beside silkscreened name of“RTC”）.<br>
@@ 第251行： / 第251行： @@
 == '''SPI test''' ==
-　　There are a group of SPI ports on MY-I.MX6 V2.5 base board，located on“J7”，silkscreened as “SPI”.<br>
+　　There are a group of SPI ports on MYZR-I.MX6 V2.5 base board，located on“J7”，silkscreened as “SPI”.<br>
@@ 第340行： / 第340行： @@
 == '''WIFI test''' ==
 === Test instruction ===
-　　Model no. of WIFI chip ussed for MY-I.MX6 evaluation board is RTL8188EUS.<br>
+　　Model no. of WIFI chip ussed for MYZR-I.MX6 evaluation board is RTL8188EUS.<br>
 === Test method ===
 ）Load WIFI module driver <br>
@@ 第440行： / 第440行： @@
        Burning tool MfgTool-MYIMX6A9-L* svn181 and above
 </pre>
-Please refer to 《[[My-IMX6-A9 series: display functional tests|[MY-IMX6-A9 series: display functional tests]]》my-imx6-a9 series: display function test for testing
+Please refer to 《[[MYZR-IMX6-A9 series: display functional tests|[MYZR-IMX6-A9 series: display functional tests]]》my-imx6-a9 series: display function test for testing
 *In general, it is tested as follows:
@@ 第534行： / 第534行： @@
 = '''Instruction about environment variables''' =
 ----
-== Features of environment variables of MY-IMX6 series of development board ==
+== Features of environment variables of MYZR-IMX6 series of development board ==
-　　Environment variables of MY-IMX6 series of development board feature as below：<br>
+　　Environment variables of MYZR-IMX6 series of development board feature as below：<br>
 . medium leading kernel includes：eMMC、network（tftp）<br>
 . medium leading file system includes：eMMC、network（NFS）<br>

@@ 第432行： / 第432行： @@
 = '''Reveal function test''' =
 ----
-Special notes:
+*Special notes:
 <pre>
 When  u-boot  version u-boot-2016.03 svn315 and above
@@ 第438行： / 第438行： @@
                        Linux -3.14.52 svn369 and above
                        Linux -3.14.52 svn368 and above
-       Burning tool MfgTool- myimx6a9-l * svn181 and above
+       Burning tool MfgTool-MYIMX6A9-L* svn181 and above
 </pre>
-Please refer to my-imx6-a9 series: display function test for testing
+Please refer to 《[[My-IMX6-A9 series: display functional tests|[MY-IMX6-A9 series: display functional tests]]》my-imx6-a9 series: display function test for testing
-In general, it is tested as follows:
+*In general, it is tested as follows:
 　　Instruction：need to re-boot system to enter u-boot command line for each reveal function test，enter command and press Enter key.<br>
 　　Example as below：.<br>

@@ 第432行： / 第432行： @@
 = '''Reveal function test''' =
 ----
 　　Instruction：need to re-boot system to enter u-boot command line for each reveal function test，enter command and press Enter key.<br>
 　　Example as below：.<br>

@@ 第3行： / 第3行： @@
 = '''Preparation before test''' =
 ----
-:1）Please refer to "connection of device"->"Linux fast boot"  in 《Linux fast boot manual》 for the connection.br>
+:1）Please refer to "connection of device"->"Linux fast boot"  in 《Linux fast boot manual》 for the connection.<br>
 :2）Please refer to "booting device" ->"Linux fast boot" in 《Linux fast boot manual》 for the booting.<br>
@@ 第19行： / 第19行： @@
 Connect lan line：connect “P4”on evaluation board with computer lan port through network<br>
 Set computer IP：set computer lan port IP as 192.168.3.9 <br>
-[[File::MY-IMX6-EK200 L3035_2.1.2.1.png]]<br>
+[[File:MY-IMX6-EK200 L3035_2.1.2.1.png]]<br>
 *Run test command ：$ ping -I eth0 192.168.3.9 -c 2 -w 4<br>
 Observe test result：system will output following information：<br>
@@ 第29行： / 第29行： @@
 ）Test the second ethernet lan port.<br>
 * Connect lan line：take out lan line from the first lan port then plug in “P5”on evaluation board，another end of lan line is kept in connection with lan port of computer.<br>
-* Set computer IP：set computer lan port IP as 192.168.3.9（if the setting was already done then go direclty into next step）.<br>
+* Set computer IP：set computer lan port IP as 192.168.3.9（If the setting was already done then go direclty into next step）.<br>
 * Set the second lan port IP：$ ifconfig eth1 192.168.3.18，after the setting system will output working condition of the second lan port, as below：<br>
 smsc95xx 2-1.1:1.0: eth1: link up, 100Mbps, full-duplex, lpa 0xCDE1<br>
@@ 第47行： / 第47行： @@
 　　The fifth red frame is test command for lan port2.<br>
-[[File::MY-IMX6-EK200 L3035_2.1.3.1.png]]<br>
+[[File:MY-IMX6-EK200 L3035_2.1.3.1.png]]<br>
@@ 第69行： / 第69行： @@
 　　The third red frame in image is message outputed by system when insert USB mouse.<br>
 　　The fourth red frame in image is message outputed by system when take out USB mouse.<br>
-[[File::MY-IMX6-EK200 L3035_2.2.3.1.png]]<br>
+[[File:MY-IMX6-EK200 L3035_2.2.3.1.png]]<br>
 == '''SD card interface test''' ==
@@ 第92行： / 第92行： @@
 === reference symbols ===
-[[File::MY-IMX6-EK200 L3035_2.3.3.1.png]]<br>
+[[File:MY-IMX6-EK200 L3035_2.3.3.1.png]]<br>
 == '''A/V test''' ==
 ===  Test instruction ===
@@ 第111行： / 第111行： @@
 ===  reference symbols ===
-[[File::MY-IMX6-EK200 L3035_2.4.3.1.png]]<br>
+[[File:MY-IMX6-EK200 L3035_2.4.3.1.png]]<br>
 == '''LED（GPIO）test''' ==
 ===  Test instruction ===
@@ 第133行： / 第133行： @@
 ===  reference symbols ===
-[[File::MY-IMX6-EK200 L3035_2.5.3.1.png]]<br>
+[[File:MY-IMX6-EK200 L3035_2.5.3.1.png]]<br>
 == '''Key test''' ==
 ===  Test instruction ===
@@ 第155行： / 第155行： @@
 ===  reference symbols ===
-[[File::MY-IMX6-EK200 L3035_2.6.3.1.png]]<br>
+[[File:MY-IMX6-EK200 L3035_2.6.3.1.png]]<br>
 == '''Serial port test''' ==
 :There are 5 serial ports in MY-I.MX6 evaluation board，4 are user serial ports（in “J1”in front view of base board，silkscreened as“TTL_UART”），one is debug serial port（in “P2”in front view of base board）.<br>
@@ 第187行： / 第187行： @@
 === reference symbols ===
-[[File::MY-IMX6-EK200 L3035_2.7.3.1.png]]<br>
+[[File:MY-IMX6-EK200 L3035_2.7.3.1.png]]<br>
 == '''RTC test''' ==
 === Test instruction ===
@@ 第214行： / 第214行： @@
 ===  reference symbols ===
 Below image is screenshots for step1 and step 2 in the test.<br>
-[[File::MY-IMX6-EK200 L3035_2.8.3.1.png]]<br>
+[[File:MY-IMX6-EK200 L3035_2.8.3.1.png]]<br>
 	Below image is the screenshots for step3 in the test.<br>
-[[File::MY-IMX6-EK200 L3035_2.8.3.2.png]]<br>
+[[File:MY-IMX6-EK200 L3035_2.8.3.2.png]]<br>
@@ 第247行： / 第247行： @@
 ）figure <br>
-[[File::MY-IMX6-EK200 L3035_2.9.3.1.png]]<br>
+[[File:MY-IMX6-EK200 L3035_2.9.3.1.png]]<br>
@@ 第279行： / 第279行： @@
 === Figured ===
-[[File::MY-IMX6-EK200 L3035_2.10.3.1.png]]<br>
+[[File:MY-IMX6-EK200 L3035_2.10.3.1.png]]<br>
 == '''CAN interface test''' ==
 === Test instruction ===
@@ 第298行： / 第298行： @@
 === Figured ===
-[[File::MY-IMX6-EK200 L3035_2.11.3.1.png]]<br>
+[[File:MY-IMX6-EK200 L3035_2.11.3.1.png]]<br>
 == '''PCIE interface test''' ==
 === Test instruction ===
@@ 第329行： / 第329行： @@
 ===figured ===
 Following figure is message outputed by system without a link with PCI-E device.<br>
-[[File::MY-IMX6-EK200 L3035_2.12.3.1.png]]<br>
+[[File:MY-IMX6-EK200 L3035_2.12.3.1.png]]<br>
 <br>
 The following figure is message ouputed by system with a link to Intel 4965AGN.<br>
-[[File::MY-IMX6-EK200 L3035_2.12.3.2.png]]<br>
+[[File:MY-IMX6-EK200 L3035_2.12.3.2.png]]<br>
 <br>
 	Following figure is message by use of lspci after entering system on the condition of a link with Intel 4965AGN.<br>
-[[File::MY-IMX6-EK200 L3035_2.12.3.3.png]]<br>
+[[File:MY-IMX6-EK200 L3035_2.12.3.3.png]]<br>
@@ 第367行： / 第367行： @@
 === Figured ===
-[[File::MY-IMX6-EK200 L3035_2.13.3.1.png]]<br>
+[[File:MY-IMX6-EK200 L3035_2.13.3.1.png]]<br>
 <br>
-[[File::MY-IMX6-EK200 L3035_2.13.3.2.png]]<br>
+[[File:MY-IMX6-EK200 L3035_2.13.3.2.png]]<br>
@@ 第390行： / 第390行： @@
 === figured ===
-[[File::MY-IMX6-EK200 L3035_2.14.3.1.png]]<br>
+[[File:MY-IMX6-EK200 L3035_2.14.3.1.png]]<br>
 <br>
-[[File::MY-IMX6-EK200 L3035_2.14.3.2.png]]<br>
+[[File:MY-IMX6-EK200 L3035_2.14.3.2.png]]<br>
 == '''GPU test''' ==
@@ 第412行： / 第412行： @@
 === Figured ===
-[[File::MY-IMX6-EK200 L3035_2.15.3.1.png]]<br>
+[[File:MY-IMX6-EK200 L3035_2.15.3.1.png]]<br>
 == '''VPU test''' ==
@@ 第427行： / 第427行： @@
-=== 附图(figured) ===
+=== Figured ===
-[[File::MY-IMX6-EK200 L3035_2.16.3.1.png]]<br>
+[[File:MY-IMX6-EK200 L3035_2.16.3.1.png]]<br>
 = '''Reveal function test''' =

←上一版本	2020年10月22日 (四) 05:43的版本
（没有差异）

MYZR-IMX6-EK200 Linux-3.0.35 Test Manual - 版本历史

Admin：Admin移动页面MY-IMX6-EK200 Linux-3.0.35 Test Manual至MYZR-IMX6-EK200 Linux-3.0.35 Test Manual，不留重定向

2020年10月22日 (四) 05:43 Admin

Admin：/* Reveal function test */

Admin：/* Reveal function test */

2018年7月23日 (一) 09:06 Admin

Admin：创建页面，内容为“ = '''Preparation before test''' = ---- :1）Please refer to "connection of device"->"Linux fast boot" in 《Linux fast boot manual》 for the connection.br>...”

Admin：创建页面，内容为“
= '''Preparation before test''' = ---- :1）Please refer to "connection of device"->"Linux fast boot" in 《Linux fast boot manual》 for the connection.br>...”