Admin：Admin移动页面MY-RK3288-EK314 Android-5.1.1 Test Manual至MYZR-RK3288-EK314 Android-5.1.1 Test Manual，不留重定向

2020-10-22T08:55:48Z

Admin移动页面MY-RK3288-EK314 Android-5.1.1 Test Manual至MYZR-RK3288-EK314 Android-5.1.1 Test Manual，不留重定向

2020年10月22日 (四) 08:55 Admin

2020-10-22T08:55:41Z

Admin：创建页面，内容为“
= '''Preparation before test''' = ---- 1）Prepare a set of MY-RK3288-EK314 development board, 5V DC power supply, USB to serial cable.
2）Connect the se...”

2018-07-24T06:53:02Z

创建页面，内容为“<div> = '''Preparation before test''' = ---- 1）Prepare a set of MY-RK3288-EK314 development board, 5V DC power supply, USB to serial cable. 2）Connect the se...”

新页面

<div>

= '''Preparation before test''' =
----
1）Prepare a set of MY-RK3288-EK314 development board, 5V DC power supply, USB to serial cable. 
2）Connect the serial cable to the development board and power. 

= '''Test item''' =
----
== '''Network inferface test''' ==
MY-RK3288-EK314 support two ethernet interfaces, one is 100 Mbps ethernet, the other is 1 Gbps ethernet. 

=== Interface property ===
{| class="wikitable"
|-
!span style="color:#FFFFFF;background:#000080"|Evaluation board model no.
!span style="color:#FFFFFF;background:#000080"|Interface position
!span style="color:#FFFFFF;background:#000080"|Interface rate standard
!span style="color:#FFFFFF;background:#000080"|System interface
|-
|rowspan=2|MY-RK3288-EK314
|U13
|10/100/1000Mbps
|eth0
|-

|P1
|10/100Mbps
|eth1
|}

=== Test method ===
1）Test instruction 
*Need to use a router, the default gateway is 192.168.137.1 

2）Eth0 connect test 
*Connect lan line: connect “eth0”on evaluation board with corresponding network router with lan line. 

*Figure 
[[File:my-rk32-ek314_android_test_2.1.2.png|642px]] 

3） Eth1 connect test 
*Connect lan line：insert one end of lan line into “eth1”on evaluation board and another end into network router. 

*Set the second network inter face IP： 
＃ ifconfig eth1 192.168.137.100 　　　＃ configure the eth1 
＃ ping -I eth1 192.168.137.1 　　　　　＃ send ICMP to HOST 

*Figures 
[[File:my-rk32-ek314_android_test_2.1.3.png|642px]] 

== '''USB test''' ==
=== Interface property ===
{| class="wikitable"
|-
!span style="color:#FFFFFF;background:#000080"|Evaluation board model no.
!span style="color:#FFFFFF;background:#000080"|Interface position
!span style="color:#FFFFFF;background:#000080"|Interface rate standard
|-
|MY-RK3288-EK314
|J10
|480 Mbits/s
|}

=== Test method ===
1）Start test 
Insert USB device into USB port on base board，enter the following command： 

2）Test over 
Instruction：when plug in & out U disk from USB interface 

=== Figure ===
[[File:my-rk32-ek314_android_test_2.2.1.png|642px]] 

== '''SD card test''' ==
=== Interface property ===
{| class="wikitable"
{| class="wikitable"
|-
!span style="color:#FFFFFF;background:#000080"|Evaluation model no.

!span style="color:#FFFFFF;background:#000080"|Interface position

!span style="color:#FFFFFF;background:#000080"|Interface type
|-

|MY-RK3288-EK314

|U22

|SD
|}
|}

=== Start test ===
1）Insert device into SD card slot 
Insert SD card into SD card port on base board 

2）Test over 
Take out SD card after SD card pop-pup,then test is over. 

=== Figures ===
[[File:my-rk32-ek314_android_test_2.3.1.png|642px]] 

== '''Audio test''' ==
Click “Setting”->“Display”->“Brightness level” 

===Figures ===
[[File:my-rk32-ek314_android_test_2.4.1.png|642px]] 

== '''Audio test''' ==
=== Test instruction ===
The test is to verify audio function of evaluation board by playing audio file. 

=== Test method ===
1）Prepare test 
Connect audio output device to audio element in front view of base board,audio element is “J20”in front view of base board. 

2）Execute test 
Prepare the mp3 audio file with the USB drive, plug in the USB drive and directly open the mp3 file . 
=== Figures ===
[[File:my-rk32-ek314_android_test_2.5.1.png|642px]] 

== '''Standard GPIO test''' ==
=== Interface property ===
{| class="wikitable"
|-
|span style="color:#FFFFFF;background:#000080"|Evaluation model no.
|span style="color:#FFFFFF;background:#000080"|LED label
|span style="color:#FFFFFF;background:#000080"|GPIO property
|span style="color:#FFFFFF;background:#000080"|IO order number
|-
|rowspan=4|MY-RK3288-EK314
|D1 ||GPIO0_B1 ||9
|-
|D2 ||GPIO0_C2 ||18
|-
|D3 ||GPIO0_B0 ||8
|-
|D4 ||GPIO0_A7 ||7
|}

=== TTest method ===
1）GPIO output test 

*Set IO order number for GPIO of which need to be tested. 
＃ OUT_IO_NUMBER=9 

*Lead out GPIO 
＃ echo ${OUT_IO_NUMBER} > /sys/class/gpio/export 

*Set GPIO direction 
＃ echo out > /sys/class/gpio/gpio${OUT_IO_NUMBER}/direction 

*Control outputed electrical level 
＃ echo 0 > /sys/class/gpio/gpio${OUT_IO_NUMBER}/value 
＃ echo 1 > /sys/class/gpio/gpio${OUT_IO_NUMBER}/value 
[[File:my-rk32-ek314_android_test_2.6.1.png|642px]] 

2）GPIO input test 
*Set IO order number for GPIO of which need to be tested . 
＃ IN_IO_NUMBER=18 

*Lead out GPIO 
＃ echo ${IN_IO_NUMBER} > /sys/class/gpio/export 

*Set GPIO direction 
＃ echo in > /sys/class/gpio/gpio${IN_IO_NUMBER}/direction 

*Check inputed electrical level 
cat /sys/class/gpio/gpio${IN_IO_NUMBER}/value 
[[File:my-rk32-ek314test_2.5.2.png|642px]] 

== '''GPIO-KEY test''' ==
=== Interface property ===
{| class="wikitable"
|-
!colspan=3;span style="background:#ffff00"|MY-RK3288-EK314
|-
|span style="color:#FFFFFF;background:#000080"|Interface position
|span style="color:#FFFFFF;background:#000080"|GPIO property
|span style="color:#FFFFFF;background:#000080"|KEY property

|-
|SW1
|gpio-keys
|Volume Down
|-
|SW2
|gpio-keys
|Volume Up
|-
|SW3
|gpio-keys
|Power
|-
|SW4
|gpio-keys
|Reset
|-
|SW5
|gpio-keys
|Recovery
|}

=== Test method ===
Press SW1 and SW2 
=== Figures ===
[[File:my-rk32-ek314_android_test_2.7.1.png|642px]] 

== '''Serial port test''' ==
MY-RK3288-EK314 has total 5 serial ports，one is debug seiral port，the other 4 are user serial ports. 

=== User serial port property ===
{| class="wikitable"
|-
!span style="color:#FFFFFF;background:#000080"|Evaluation board model no.
!span style="color:#FFFFFF;background:#000080"|UARTx
!span style="color:#FFFFFF;background:#000080"|Hardware interface
!span style="color:#FFFFFF;background:#000080"|System interface
|-
|rowspan=4|MY-RK3288-EK314
|UART0
|BT (Bluetooth)
|ttyS0
|-

|UART1
|P3
|ttyS1
|-

|UART2
|P4 (DEBUG)
|ttyS2
|}

Tips：transceiver pins of serial port are listed here,but please refer to schematic for definition of all pins of serial port. 

=== Serial port test ===
*Install uart APK 

*Figures 
[[File:my-rk32-ek314_android_test_2.8.1.png|642px]] 
[[File:my-rk32-ek314_android_test_2.8.2.png|642px]] 

== '''RTC test ''' ==
=== Test instruction ===
Due to restrictions in transportation，MY-RK3288-EK314 evaluation board doesn't contatin battery in delivery。before RTC test please prepare button cell to install on evaluation board。 
MY-RK3288-EK314 battery holder is located in“BT1”on front view of base board. 

=== Test method ===
1）Power on, and look at the"clock" 
*Figures 
[[File:my-rk32-ek314_android_test_2.9.1.png|642px]] 
2）Power off ,wait for a while and power on 
*Figures 
[[File:my-rk32-ek314_android_test_2.9.2.png|642px]] 

== '''SPI test ''' ==
MY-RK3288-EK314 has two groups of SPI interfaces. 

=== Interface property ===
Pins of MISO and MOSI need to be used for test,listed as below. 
{| class="wikitable"
|-
!span style="color:#FFFFFF;background:#000080"|Evaluation board model no.
!span style="color:#FFFFFF;background:#000080"|SPIx
!span style="color:#FFFFFF;background:#000080"|MISO
!span style="color:#FFFFFF;background:#000080"|MOSI
!span style="color:#FFFFFF;background:#000080"|System interface
|-
|rowspan=2|MY-RK3288-EK314
|SPI1
|J11:33
|J11:35
|spidev0.0
|-

|SPI2
|J11:38
|J13:34
|spidev2.0
|}

=== Test specification ===
1）Adopt way of SPI self-sending(output)self-receiving(input). 
Note：the test need a short connection of evaluation board pins,if you are not sure of how to conduct this kind of connection,please ask hardware engineer for a support,otherwise it may cause a damage of evaluation board. 

2）SPI port which is matched up with SPI test program is SPI2，e.g.SPI test is SPI2 test. 

=== Test method ===
1）Prepare test 
Short connect MISO pin and MOSI pin of SPI2. 
2）Execute test 
＃ ./spi_test -D /dev/spidev0.0 
3）Test result 
If SPI is normal,you can see following charaters on terminal： 
FF FF FF FF FF FF 
40 00 00 00 00 95 
FF FF FF FF FF FF 
FF FF FF FF FF FF 
FF FF FF FF FF FF 
DE AD BE EF BA AD 
F0 0D 

=== Figures ===
[[File:my-rk32-ek314_android_test_2.10.1.png|642px]] 

== '''Camera ov13850 test''' ==
Connect the Camera, start up, and then open the "Camera", as follows: 
*Figures 
[[File:my-rk32-ek314_android_test_2.11.1.png|642px]] 

== '''WIFI test''' ==
The WIFI chip model used on the MY-RK3288-EK314 evaluation board is AP6335. 
1）Step 1 
Click "Settings" -> "Wi-Fi" to open the WIFI switch. 
[[File:my-rk32-ek314_android_test_2.12.1.png|642px]] 

2）Step 2 
Enter WIFI password and connect successfully. 
[[File:my-rk32-ek314_android_test_2.12.2.png|642px]] 
[[File:my-rk32-ek314_android_test_2.12.3.png|642px]] 

== '''Bluetooth test''' ==
The Bluetooth chip model used on the MY-RK3288-EK314 evaluation board is AP6335. 
1）Step 1 
Click on “Settings”->“Bluetooth”,turn on Bluetooth 
[[File:my-rk32-ek314_android_test_2.13.1.png|642px]] 
2）Step 2 
Match 
[[File:my-rk32-ek314_android_test_2.13.2.png|642px]] 
3）Step 3 
Send and receive files 
[[File:my-rk32-ek314_android_test_2.13.3.png|642px]] 
[[File:my-rk32-ek314_android_test_2.13.4.png|642px]] 

== '''4G internet module test''' ==
=== Test instruction ===
Test online 4G module, such as L506. 

=== Test method ===
*Power on with the module, display 3G logo. 
[[File:my-rk32-ek314_android_test_2.14.1.png|642px]] 

== '''HDMI test''' ==
=== Test instruction ===
Connect HDMI. 

=== Test method ===
*Burn resource-hdmi.img 
Burn with AndroidTool_Release_v2.35. 

*Test 
Power on, HDMI has display image. 

*Modify the resolution 
To modify the resolution, modify arch/arm/boot/dts/lcd-box.dtsi. 

== '''EDP test''' ==
=== Test instruction ===
Connect EDP. 

=== Test method ===
*Burn resource-edp.img 
Burn with AndroidTool_Release_v2.35. 

*Test 
Power on, EDP has display image 

*Modify the resolution 
To modify the resolution, modify arch/arm/boot/dts/lcd-EDP1080p.dtsi. 

</div>

←上一版本	2020年10月22日 (四) 08:55的版本
（没有差异）

@@ 第3行： / 第3行： @@
 = '''Preparation before test''' =
 ----
-）Prepare a set of MY-RK3288-EK314 development board, 5V DC power supply, USB to serial cable.<br>
+）Prepare a set of MYZR-RK3288-EK314 development board, 5V DC power supply, USB to serial cable.<br>
 ）Connect the serial cable to the development board and power.<br>
@@ 第9行： / 第9行： @@
 ----
 == '''Network inferface test''' ==
-MY-RK3288-EK314 support two ethernet interfaces, one is 100 Mbps ethernet, the other is 1 Gbps ethernet.<br>
+MYZR-RK3288-EK314 support two ethernet interfaces, one is 100 Mbps ethernet, the other is 1 Gbps ethernet.<br>
 === Interface property ===
@@ 第19行： / 第19行： @@
 !span style="color:#FFFFFF;background:#000080"|System interface
 |-
-|rowspan=2|MY-RK3288-EK314
+|rowspan=2|MYZR-RK3288-EK314
 |U13
 |10/100/1000Mbps
@@ 第58行： / 第58行： @@
 !span style="color:#FFFFFF;background:#000080"|Interface rate standard
 |-
-|MY-RK3288-EK314
+|MYZR-RK3288-EK314
 |J10
 |480 Mbits/s
@@ 第85行： / 第85行： @@
 |-
-|MY-RK3288-EK314
+|MYZR-RK3288-EK314
 |U22
@@ 第135行： / 第135行： @@
 |span style="color:#FFFFFF;background:#000080"|IO order number
 |-
-|rowspan=4|MY-RK3288-EK314
+|rowspan=4|MYZR-RK3288-EK314
 |D1		||GPIO0_B1		||9
 |-
@@ 第182行： / 第182行： @@
 {| class="wikitable"
 |-
-!colspan=3;span style="background:#ffff00"|MY-RK3288-EK314
+!colspan=3;span style="background:#ffff00"|MYZR-RK3288-EK314
 |-
 |span style="color:#FFFFFF;background:#000080"|Interface position
@@ 第217行： / 第217行： @@
 == '''Serial port test''' ==
-MY-RK3288-EK314 has total 5 serial ports，one is debug seiral port，the other 4 are user serial ports.<br>
+MYZR-RK3288-EK314 has total 5 serial ports，one is debug seiral port，the other 4 are user serial ports.<br>
 === User serial port property ===
@@ 第227行： / 第227行： @@
 !span style="color:#FFFFFF;background:#000080"|System interface
 |-
-|rowspan=4|MY-RK3288-EK314
+|rowspan=4|MYZR-RK3288-EK314
 |UART0
 |BT	(Bluetooth)
@@ 第254行： / 第254行： @@
 == '''RTC test ''' ==
 ===  Test instruction ===
-Due to restrictions in transportation，MY-RK3288-EK314 evaluation board doesn't contatin battery in delivery。before RTC test please prepare button cell to install on evaluation board。</span><br>
+Due to restrictions in transportation，MYZR-RK3288-EK314 evaluation board doesn't contatin battery in delivery。before RTC test please prepare button cell to install on evaluation board。</span><br>
-MY-RK3288-EK314 battery holder is located in“BT1”on front view of base board.<br>
+MYZR-RK3288-EK314 battery holder is located in“BT1”on front view of base board.<br>
@@ 第267行： / 第267行： @@
 == '''SPI test ''' ==
-MY-RK3288-EK314 has two groups of SPI interfaces.<br>
+MYZR-RK3288-EK314 has two groups of SPI interfaces.<br>
 === Interface property ===
@@ 第279行： / 第279行： @@
 !span style="color:#FFFFFF;background:#000080"|System interface
 |-
-|rowspan=2|MY-RK3288-EK314
+|rowspan=2|MYZR-RK3288-EK314
 |SPI1
 |J11:33

MYZR-RK3288-EK314 Android-5.1.1 Test Manual - 版本历史

Admin：Admin移动页面MY-RK3288-EK314 Android-5.1.1 Test Manual至MYZR-RK3288-EK314 Android-5.1.1 Test Manual，不留重定向

2020年10月22日 (四) 08:55 Admin

Admin：创建页面，内容为“ = '''Preparation before test''' = ---- 1）Prepare a set of MY-RK3288-EK314 development board, 5V DC power supply, USB to serial cable. 2）Connect the se...”

Admin：创建页面，内容为“
= '''Preparation before test''' = ---- 1）Prepare a set of MY-RK3288-EK314 development board, 5V DC power supply, USB to serial cable.
2）Connect the se...”