MYZR-R16-EK166 启动手册
目录
准备开发板套件(prepare development board kits)
开发板套件由开发板和开发板配件组成。
Development board kits consist of development board and its accessories.
开发板(development board)
开发板由以下器件组装而成：
Development board consist of following components:
- R16 开发板一块
- R16 development board,one piece
- 显示屏电路板一片
- Circuit board of screen panel,one unit
- 液晶显示屏一块
- Crystal liquid screen,one piece
- 触摸屏一片
- Touch screen,one unit
开发板配件(development board accessory)
开发板配件有：
development board accessories include:
- 电源适配器1个
- adaptor,one unit
- USB下载线1条
- USB download cable,one piece
- 网线1条
- internet cable,one piece
- 串口线1条
- serial line,one piece
开发板接口概览(overview of development board interface)
MY-R16-EK166 正面图(MY-R16-EK166 front view)：
快速启动开发板(fast boot development board)
1）检查电源是否关闭状态，确保电源开关是断开。
1)Check whether the power is off and make sure the power switch is off.
2）与计算机连接，将串口线一端连接到开发板的J7，一端连接到计算机。如果没有连接串口线，将不能通过串口方式与开发板交互。但是不影响开发板的启动及烧录系统。
2)Connect to the computer, connect one end of the serial port line to the J7 of the development board, and the other end to the computer.If there is no connection to the serial port line, you will not be able to interact with the development board in a serial port manner.However, it does not affect the starting and burning system of the development board.
3）串口终端工具配置。通过window的设备管理器找到计算机上我们使用的端口号。配置串口终端工具的各参数。
3)Serial port terminal tool configuration.Find the port number we use on the computer through the device manager of the window.Configure the parameters of the serial port terminal tool.
- SecureCRT & USB串口3 示例配置如下：
- The SecureCRT & USB serial port 3 example configuration is as follows：
4）网线连接，将网线一端连接到开发板的j12，网线另一端插入计算机的网口。
4)Connect the network cable, connect one end of the network cable to the j12 of the development board, and insert the other end of the network cable into the network port of the computer.
5）USB下载线的连接，将USB线一端连接到开发板的j8，另外一端插入计算机的USB接口。
5)The connection of the USB download line connects one end of the USB cable to the j8 of the development board and the other end to the USB interface of the computer.
6）连接电源线，将电源线一端连接到开发板的j18，一端连接电源插座。
6)Connect the power cord, connect one end of the power cord to the j18 of the development board, and one end to the power socket.
7)将开发板电源开关j17按到闭合状态。
7)Press the development board power switch j17 to the closed state.
观察启动状况(observe booting condition)
串口终端动态，会看到计算机的串口终端有开发板启动过程中输出的启动过程信息。
When the serial port terminal is dynamic, it can be seen that the serial port terminal of the computer has the startup process information output during the startup of the development board.
- 启动后串口打印信息如下：
- After starting, the serial port printing information is as follows：
- 启动后UI界面如下：
- After starting, the UI interface is as follows：
</div>
