MYZR-RZFIVE-EK200编译参考手册
来自明远智睿的wiki
MYZR-RZFIVE-EK200 Linux-5.10 编译参考手册
下载相关文件
交叉编译工具链
RZFIVE系列：打开网盘到 MYZR-RZ -> 03_SDK，下载 oecore-x86_64-riscv64-toolchain-nodistro.0.sh。
源码
u-boot源码：打开网盘到 MYZR-RZ -> 02_源码，下载 myzr-rzfive_uboot-Release.xxx.tar.bz2。
Kernel源码：打开网盘到 MYZR-RZ -> 02_源码，下载 myzr-rzfive_linux-5.10-Release.xxx.tar.bz2。
安装交叉编译工具链
执行安装
=====> Input: linyn@linyn-VirtualBox:~$ mkdir ~/riscv64-gcc linyn@linyn-VirtualBox:~$ chmod +x oecore-x86_64-riscv64-toolchain-nodistro.0.sh linyn@linyn-VirtualBox:~$ ./oecore-x86_64-riscv64-toolchain-nodistro.0.sh =====> Output:（安装路径我这边设置为/home/linyn/riscv64-gcc，可以自定义路径） OpenEmbedded SDK installer version nodistro.0 ============================================= Enter target directory for SDK (default: /usr/local/oecore-x86_64): /home/linyn/riscv64-gcc/ You are about to install the SDK to "/home/linyn/riscv64-gcc". Proceed [Y/n]? y Extracting SDK.......................................................................done Setting it up...done SDK has been successfully set up and is ready to be used. Each time you wish to use the SDK in a new shell session, you need to source the environment setup script e.g. $ . /home/linyn/riscv64-gcc/environment-setup-riscv64-oe-linux
设置交叉编译工具
=====> Input linyn@linyn-VirtualBox:~$ source /home/linyn/riscv64-gcc/environment-setup-riscv64-oe-linux
验证交叉编译工具是否设置成功
=====> Input: linyn@linyn-VirtualBox:~$ $CC -v =====> Output: Using built-in specs. COLLECT_GCC=riscv64-oe-linux-gcc COLLECT_LTO_WRAPPER=/home/linyn/riscv64-gcc/sysroots/x86_64-oesdk-linux/usr/libexec/riscv64-oe-linux/gcc/riscv64-oe-linux/8.3.0/lto-wrapper Target: riscv64-oe-linux Configured with: ../../../../../../work-shared/gcc-8.3.0-r0/gcc-8-8.3.0/src/configure --build=x86_64-linux --host=x86_64-oesdk-linux --target=riscv64-oe-linux --prefix=/usr/local/oe-sdk-hardcoded-buildpath/sysroots/x86_64-oesdk-linux/usr --exec_prefix=/usr/local/oe-sdk-hardcoded-buildpath/sysroots/x86_64-oesdk-linux/usr --bindir=/usr/local/oe-sdk-hardcoded-buildpath/sysroots/x86_64-oesdk-linux/usr/bin/riscv64-oe-linux --sbindir=/usr/local/oe-sdk-hardcoded-buildpath/sysroots/x86_64-oesdk-linux/usr/bin/riscv64-oe-linux --libexecdir=/usr/local/oe-sdk-hardcoded-buildpath/sysroots/x86_64-oesdk-linux/usr/libexec/riscv64-oe-linux --datadir=/usr/local/oe-sdk-hardcoded-buildpath/sysroots/x86_64-oesdk-linux/usr/share --sysconfdir=/usr/local/oe-sdk-hardcoded-buildpath/sysroots/x86_64-oesdk-linux/etc --sharedstatedir=/usr/local/oe-sdk-hardcoded-buildpath/sysroots/x86_64-oesdk-linux/com --localstatedir=/usr/local/oe-sdk-hardcoded-buildpath/sysroots/x86_64-oesdk-linux/var --libdir=/usr/local/oe-sdk-hardcoded-buildpath/sysroots/x86_64-oesdk-linux/usr/lib/riscv64-oe-linux --includedir=/usr/local/oe-sdk-hardcoded-buildpath/sysroots/x86_64-oesdk-linux/usr/include --oldincludedir=/usr/local/oe-sdk-hardcoded-buildpath/sysroots/x86_64-oesdk-linux/usr/include --infodir=/usr/local/oe-sdk-hardcoded-buildpath/sysroots/x86_64-oesdk-linux/usr/share/info --mandir=/usr/local/oe-sdk-hardcoded-buildpath/sysroots/x86_64-oesdk-linux/usr/share/man --disable-silent-rules --disable-dependency-tracking --with-libtool-sysroot=/b4741516c0d3/lyn-work/RENESAS/RZFive/RTK0EF0126Z0000AZJ-v1.0update1/source/build/tmp-glibc/work/x86_64-nativesdk-oesdk-linux/gcc-cross-canadian-riscv64/8.3.0-r0/recipe-sysroot --with-gnu-ld --enable-shared --enable-languages=c,c++ --enable-threads=posix --enable-multilib --enable-default-pie --enable-c99 --enable-long-long --enable-symvers=gnu --enable-libstdcxx-pch --program-prefix=riscv64-oe-linux- --without-local-prefix --disable-install-libiberty --enable-lto --disable-libssp --enable-libitm --disable-bootstrap --disable-libmudflap --with-system-zlib --with-linker-hash-style=gnu --enable-linker-build-id --with-ppl=no --with-cloog=no --enable-checking=release --enable-cheaders=c_global --without-isl --with-gxx-include-dir=/not/exist/usr/include/c++/8.3.0 --with-build-time-tools=/b4741516c0d3/lyn-work/RENESAS/RZFive/RTK0EF0126Z0000AZJ-v1.0update1/source/build/tmp-glibc/work/x86_64-nativesdk-oesdk-linux/gcc-cross-canadian-riscv64/8.3.0-r0/recipe-sysroot-native/usr/riscv64-oe-linux/bin --with-sysroot=/not/exist --with-build-sysroot=/b4741516c0d3/lyn-work/RENESAS/RZFive/RTK0EF0126Z0000AZJ-v1.0update1/source/build/tmp-glibc/work/x86_64-nativesdk-oesdk-linux/gcc-cross-canadian-riscv64/8.3.0-r0/recipe-sysroot --enable-poison-system-directories --disable-static --enable-nls --with-glibc-version=2.28 --enable-initfini-array --enable-__cxa_atexit Thread model: posix gcc version 8.3.0 (GCC)
U-BOOT编译
编译前的准备
- 创建编译工作目录
=====> Input: linyn@linyn-VirtualBox:~$ mkdir ~/source/ -p
- 解压源码包到工作目录
=====> Input: linyn@linyn-VirtualBox:~$ tar jxvf myzr-rzfive_uboot-Release.*.tar.bz2 -C ~/source/
编译U-BOOT目标文件
- 进入源码目录
=====> Input: linyn@linyn-VirtualBox:~$ cd ~/source/myzr-rzfive_uboot-2020.10
- 清除配置
=====> Input: linyn@linyn-VirtualBox:~/source/myzr-rzfive_uboot-2020.10$ ./build.sh rzfive 2g clean =====> Output: ============Start build clean============ CLEAN dts/../arch/riscv/dts CLEAN dts CLEAN examples/standalone CLEAN tools CLEAN tools/lib tools/common CLEAN spl/arch spl/board spl/cmd spl/common spl/disk spl/drivers spl/dts spl/env spl/fs spl/lib spl/u-boot.cfg spl/u-boot-spl spl/u-boot-spl.bin spl/u-boot-spl.dtb spl/u-boot-spl-dtb.bin spl/u-boot-spl.lds spl/u-boot-spl.map spl/u-boot-spl-nodtb.bin CLEAN u-boot.lds u-boot.dtb u-boot.cfg.configs u-boot-dtb.img u-boot.map u-boot.itb u-boot.its u-boot.srec u-boot.cfg u-boot.bin u-boot-dtb.bin u-boot-nodtb.bin u-boot u-boot.img u-boot-spl_bp.bin u-boot.sym System.map CLEAN scripts/basic CLEAN scripts/dtc CLEAN scripts/kconfig CLEAN include/config include/generated spl CLEAN .config .config.old include/autoconf.mk include/autoconf.mk.dep include/config.h ====Build clean ok!====
- 生成目标开发板的 .config 文件
=====> Input: linyn@linyn-VirtualBox:~/source/myzr-rzfive_uboot-2020.10$ ./build.sh rzfive 2g config =====> Output: ============Start build config============ HOSTCC scripts/basic/fixdep HOSTCC scripts/kconfig/conf.o YACC scripts/kconfig/zconf.tab.c LEX scripts/kconfig/zconf.lex.c HOSTCC scripts/kconfig/zconf.tab.o HOSTLD scripts/kconfig/conf # # configuration written to .config # ====Build config ok!====
【注意】：上面2g 是内存配置，改为与开发板型号对应的配置文件，还有内存1g的配置。
********** MYZR-RZFIVE-EK200 ********** myzr-rzfive-1g_defconfig myzr-rzfive-2g_defconfig
- 执行编译
=====> Input:
linyn@linyn-VirtualBox:~/source/myzr-rzfive_uboot-2020.10$ ./build.sh rzfive 2g uboot
=====> Output:
==========Start build uboot==========
scripts/kconfig/conf --silentoldconfig Kconfig
......
CC spl/drivers/mmc/sh_sdhi.o
LD spl/drivers/timer/built-in.o
LD spl/drivers/mmc/built-in.o
LD spl/drivers/built-in.o
LD spl/u-boot-spl
OBJCOPY spl/u-boot-spl-nodtb.bin
CAT spl/u-boot-spl-dtb.bin
COPY spl/u-boot-spl.bin
====Build uboot ok!====
===target image:spl-myzr-rzfive-2g.srec and fit-myzr-rzfive-2g.srec=====
- 目标文件
=====> Input: linyn@linyn-VirtualBox:~/source/myzr-rzfive_uboot-2020.10$ ls EK200_IMAGE/ =====> Output: fit-myzr-rzfive-2g.srec spl-myzr-rzfive-2g.srec
Note: 如果有提示 “cc1: error”，通常是交叉编译工具的配置没生效，可以按前面 “交叉编译工具链安装” 中的 “source 工具链配置文件” 操作一次后再执行此步骤。
注意：还可以一次性完整编译
=====> Input:
linyn@linyn-VirtualBox:~/source/myzr-rzfive_uboot-2020.10$ ./build.sh all
=====> Output:
=========Start build all=========
============Start build clean============
====Build clean ok!====
============Start build config============
HOSTCC scripts/basic/fixdep
...
====Build uboot ok!====
===target image:spl-myzr-rzfive-2g.srec and fit-myzr-rzfive-2g.srec=====
=========build all ok=========
内核编译
编译前的准备
- 创建编译工作目录
=====> Input: mkdir ~/source/ -p
- 解压源码包到工作目录
=====> Input: linyn@linyn-VirtualBox:~$ tar jxvf myzr-rzfive_linux-5.10-Release.*.tar.bz2 -C ~/source/ linyn@linyn-VirtualBox:~$ sudo apt-get install libssl-dev
编译内核目标文件
- 进入内核源码目录
=====> Input: linyn@linyn-VirtualBox:~$ cd ~/source/myzr-rzfive_linux-5.10/
- 清除配置
=====> Input: linyn@linyn-VirtualBox:~/source/myzr-rzfive_linux-5.10$ ./build.sh rzfive 2g clean =====> Output: ============Start build clean============ ====Build clean ok!====
- 编译内核
=====> Input: linyn@linyn-VirtualBox:~/source/myzr-rzfive_linux-5.10$ ./build.sh rzfive 2g kernel =====> Output: ============Start build kernel=========== HOSTCC scripts/basic/fixdep HOSTCC scripts/kconfig/conf.o HOSTCC scripts/kconfig/confdata.o HOSTCC scripts/kconfig/expr.o LEX scripts/kconfig/lexer.lex.c ...... LD vmlinux SYSMAP System.map OBJCOPY arch/riscv/boot/Image Kernel: arch/riscv/boot/Image is ready ====Build kernel ok!====
- 内核目标文件 EK200_IMAGE/Image 即内核目标文件
编译设备树目标文件
- 执行编译命令
=====> Input: linyn@linyn-VirtualBox:~/source/myzr-rzfive_linux-5.10$ ./build.sh rzfive 2g dtb =====> Output: ==========Start build dtb========== DTC arch/riscv/boot/dts/renesas/myzr-rzfive-2g.dtb ====Build dtb ok!====
【注意】：上面 2g改为与开发板型号对应的配置文件。
- 目标文件
********** MYZR-RZFIEV-EK200 ********** EK200_IMAGE/myzr-rzfive-1g.dtb EK200_IMAGE/myzr-rzfive-2g.dtb
编译内核模块包
- 执行编译命令
=====> Input: linyn@linyn-VirtualBox:~/source/myzr-rzfive_linux-5.10$ ./build.sh rzfive 2g modules =====> Output: ==========Start build modules========== CALL scripts/atomic/check-atomics.sh CALL scripts/checksyscalls.sh ...... INSTALL fs/efivarfs/efivarfs.ko DEPMOD 5.10.145-cip17-riscv-renesas ====Build modules oks!====
- 目标文件
EK200_IMAGE/kernel-modules.tar.bz2
注意：还可以一次性完整编译
=====> Input: linyn@linyn-VirtualBox:~/source/myzr-rzfive_linux-5.10$ ./build.sh rzfive 2g all =====> Output: =========Start build all========= ============Start build clean============ CLEAN arch/riscv/kernel/vdso CLEAN arch/riscv/kernel CLEAN certs ... INSTALL fs/configfs/configfs.ko INSTALL fs/efivarfs/efivarfs.ko DEPMOD 5.10.145-cip17-riscv-renesas ====Build modules oks!==== =========build all ok=========
Linux C程序编译
准备源码
打开网盘到 5_MY-Demo -> MY-Linux-C-Demo，下载 hello.c 文件，并复制到虚拟机。
编译目标文件
=====> Input: linyn@linyn-VirtualBox:~/source$ $CC hello.c -o hello.out
Note: 如果有“未找到命令”的信息，是因为交叉编译工具链的配置没有生效，可以按前面 “交叉编译工具链安装” 中的 “source 工具链配置文件” 操作一次后再执行此步骤
运行Linux C目标程序
- 把编译得到的 hello.out 复制到开发板上
- 在开发板上运行Linux C目标程序
=====> Input: linyn@linyn-VirtualBox:~/source$ chmod +x ./hello.out linyn@linyn-VirtualBox:~/source$ ./hello.out =====> Output: MYZR Technology Co.,Ltd. Web: http://www.myzr.com.cn/ Wiki: http://wiki.myzr.com.cn/ BBS: http://bbs.myzr.com.cn/ Tel: 0756-3628023/3628021 E-mail: service@myzr.com.cn
