“MYZR-A40I-EK204 Linux-3.10.65 测试手册”的版本间的差异
(创建页面,内容为“### 网口测试 【测试说明】:采用开发板向PC发送ICMP报文的方式进行测试<br> 【接口标识】:10M/100M Ethernet-1<br> ...”) |
(没有差异)
|
2021年7月15日 (四) 14:53的最新版本
目录
网口测试
【测试说明】:采用开发板向PC发送ICMP报文的方式进行测试
【接口标识】:10M/100M Ethernet-1
【系统接口】:eth0
测试操作
配置电脑有线网卡IP为 192.168.137.99。
把开发板的这个网口用网线跟电脑网口连接起来。
配置开发板网口:
=====> 输入指令: ifconfig eth0 192.168.137.81
测试网口:
=====> 输入指令: ping 192.168.137.99 -c 2 -w 4 =====> 输出信息: PING 192.168.137.99 (192.168.137.99) 56(84) bytes of data. 64 bytes from 192.168.137.99: icmp_seq=1 ttl=128 time=0.570 ms 64 bytes from 192.168.137.99: icmp_seq=2 ttl=128 time=0.365 ms --- 192.168.137.99 ping statistics --- 2 packets transmitted, 2 received, 0% packet loss, time 999ms rtt min/avg/max/mdev = 0.365/0.467/0.570/0.104 ms
测试结果
“0% packet loss”表示测试通过。
USB接口测试
【测试说明】:采用插拔USB存储设备(U盘)的方式进行测试
【接口标识】:USB HOST
【系统接口】:/sys/bus/usb/
测试方法
将USB设备插入底板USB接口,系统会输出类似如下信息:
root@TinaLinux:/# [ 795.551264] ehci_irq: highspeed device connect [ 795.910089] usb 1-1: new high-speed USB device number 4 using sunxi-ehci [ 796.081676] usb-storage 1-1:1.0: USB Mass Storage device detected [ 796.110678] scsi1 : usb-storage 1-1:1.0 [ 797.111474] scsi 1:0:0:0: Direct-Access Kingston DataTraveler 3.0 PMAP PQ: 0 ANSI: 6 [ 797.140157] sd 1:0:0:0: [sda] 60604416 512-byte logical blocks: (31.0 GB/28.8 GiB) [ 797.156371] sd 1:0:0:0: [sda] Write Protect is off [ 797.161892] sd 1:0:0:0: [sda] Mode Sense: 45 00 00 00 [ 797.169966] sd 1:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 797.251578] sda: sda1 [ 797.260467] CPU1: Booted secondary processor [ 797.271003] sd 1:0:0:0: [sda] Attached SCSI removable disk [ 797.489583] sda: sda1 [ 797.622161] FAT-fs (sda1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck. [ 797.860430] CPU2: Booted secondary processor [ 797.974464] FAT-fs (sda1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
将USB设备从底板拔出,系统会输出类似如下信息:
[ 810.557018] ehci_irq: highspeed device disconnect [ 810.562361] usb 1-1: USB disconnect, device number 4 [ 810.670680] udevd[2861]: inotify_add_watch(6, /dev/sda, 10) failed: No such file or directory
测试结果
USB存储设备插拔时系统输出如上类似信息即表示正常。
TF接口测试
【测试说明】:采用插入并识别TF卡的方式进行测试
【接口标识】:SD3
【系统接口】:/sys/bus/mmc/
测试方法
把TF卡插入到这个接口:
=====> 输出信息: root@TinaLinux:/# [ 80.560114] sunxi-mmc sdc0: sdc set ios: clk 0Hz bm PP pm UP vdd 22 width 1 timing LEGACY(SDR12) dt B [ 80.590139] sunxi-mmc sdc0: sdc set ios: clk 400000Hz bm PP pm ON vdd 22 width 1 timing LEGACY(SDR12) dt B [ 80.620937] sunxi-mmc sdc0: smc 1 p0 err, cmd 52, RTO !! [ 80.627845] sunxi-mmc sdc0: smc 1 p0 err, cmd 52, RTO !! [ 80.634740] sunxi-mmc sdc0: sdc set ios: clk 400000Hz bm PP pm ON vdd 22 width 1 timing LEGACY(SDR12) dt B [ 80.653529] sunxi-mmc sdc0: sdc set ios: clk 400000Hz bm PP pm ON vdd 22 width 1 timing LEGACY(SDR12) dt B [ 80.670770] sunxi-mmc sdc0: smc 1 p0 err, cmd 5, RTO !! [ 80.677415] sunxi-mmc sdc0: smc 1 p0 err, cmd 5, RTO !! [ 80.687485] sunxi-mmc sdc0: smc 1 p0 err, cmd 5, RTO !! [ 80.694393] sunxi-mmc sdc0: smc 1 p0 err, cmd 5, RTO !! [ 80.702493] sunxi-mmc sdc0: sdc set ios: clk 400000Hz bm PP pm ON vdd 15 width 1 timing LEGACY(SDR12) dt B [ 80.714629] sunxi-mmc sdc0: sdc set ios: clk 400000Hz bm PP pm ON vdd 15 width 1 timing LEGACY(SDR12) dt B [ 80.733353] sunxi-mmc sdc0: sdc set ios: clk 400000Hz bm PP pm ON vdd 15 width 1 timing LEGACY(SDR12) dt B [ 80.750809] CPU1: Booted secondary processor [ 80.943958] mmc1: host does not support reading read-only switch. assuming write-enable. [ 80.958125] sunxi-mmc sdc0: sdc set ios: clk 400000Hz bm PP pm ON vdd 15 width 1 timing SD-HS(SDR25) dt B [ 80.970520] sunxi-mmc sdc0: sdc set ios: clk 50000000Hz bm PP pm ON vdd 15 width 1 timing SD-HS(SDR25) dt B [ 80.982111] sunxi-mmc sdc0: sdc set ios: clk 50000000Hz bm PP pm ON vdd 15 width 4 timing SD-HS(SDR25) dt B [ 80.993313] mmc1: new high speed SDHC card at address aaaa [ 80.999904] mmcblk1: mmc1:aaaa SC16G 14.8 GiB [ 81.013518] mmcblk1: [ 81.016702] sndhdmi sndhdmi: ASoC: CPU DAI (null) not registered [ 81.023541] sndhdmi sndhdmi: snd_soc_register_card() failed: -517 [ 81.030614] platform sndhdmi: Driver sndhdmi requests probe deferral [ 81.103148] FAT-fs (mmcblk1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
弹出TF卡:
=====> 输出信息: root@TinaLinux:/# [ 147.600144] sunxi-mmc sdc0: smc 1 p0 err, cmd 13, RTO !! [ 147.606083] sunxi-mmc sdc0: smc 1 p0 err, cmd 13, RTO !! [ 147.612251] sunxi-mmc sdc0: smc 1 p0 err, cmd 13, RTO !! [ 147.618180] sunxi-mmc sdc0: smc 1 p0 err, cmd 13, RTO !! [ 147.624573] mmc1: card aaaa removed [ 147.637669] sunxi-mmc sdc0: sdc set ios: clk 0Hz bm OD pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
TF存储设备插拔时系统输出如上类似信息即表示正常。
标准GPIO测试
【测试说明】:控制GPIO的输出电平
【接口标识】:GPIO/SD2
【系统接口】:/sys/class/gpio/
GPIO输出低电平测试
配置P26:2为输出低电平的操作方法:
=====> 输入指令: OUT_IO_OUT_NUM=270 echo ${OUT_IO_OUT_NUM} > /sys/class/gpio/export echo "out" > /sys/class/gpio/gpio${OUT_IO_OUT_NUM}/direction echo 0 > /sys/class/gpio/gpio${OUT_IO_OUT_NUM}/value
用万用表测试管脚P26:2,电压为0V,则表示OK
GPIO输出高电平测试
配置P26:2为输出高电平的操作方法:
=====> 输入指令: OUT_IO_OUT_NUM=270 echo ${OUT_IO_OUT_NUM} > /sys/class/gpio/export echo "out" > /sys/class/gpio/gpio${OUT_IO_OUT_NUM}/direction echo 1 > /sys/class/gpio/gpio${OUT_IO_OUT_NUM}/value
用万用表测试管脚P26:2,电压为3.3V,则表示OK
其它
控制 GPIO 输出低电平的指令:
=====> 输入指令: echo 0 > /sys/class/gpio/gpio${OUT_IO_OUT_NUM}/value
控制 GPIO 输出高电平的指令:
=====> 输入指令: echo 1 > /sys/class/gpio/gpio${OUT_IO_OUT_NUM}/value
GPIO-LED测试
【测试说明】:控制LED
【接口标识】:LED
【系统接口】:/sys/class/leds/led*
测试操作
控制LED关闭:
echo 1 > /sys/class/leds/led1/brightness echo 1 > /sys/class/leds/led2/brightness echo 1 > /sys/class/leds/led3/brightness
控制LED开启:
echo 0 > /sys/class/leds/led1/brightness echo 0 > /sys/class/leds/led2/brightness echo 0 > /sys/class/leds/led3/brightness
GPIO-KEY测试
【测试说明】:使用 evtest 进行测试
【接口标识】:KEY4, KEY4, KEY3, KEY2, KEY1
【系统接口】:/dev/input/event0
测试操作
运行 evtest 准备测试
=====> 输入指令: evtest =====> 输出信息: No device specified, trying to scan all of /dev/input/event* Available devices: /dev/input/event0: sunxi-keyboard /dev/input/event1: sunxi-ir /dev/input/event2: axp22-powerkey Select the device event number [0-2]:
选择 sunxi-keyboard 所对应的序号
=====> 输入指令: 0 =====> 输出信息: Input driver version is 1.0.1 Input device ID: bus 0x19 vendor 0x1 product 0x1 version 0x100 Input device name: "sunxi-keyboard" Supported events: Event type 0 (EV_SYN) Event type 1 (EV_KEY) Event code 28 (KEY_ENTER) Event code 102 (KEY_HOME) Event code 114 (KEY_VOLUMEDOWN) Event code 115 (KEY_VOLUMEUP) Event code 139 (KEY_MENU) Properties: Testing ... (interrupt to exit)
按动开发板上的按键
Event: time 1262304222.998060, type 1 (EV_KEY), code 102 (KEY_HOME), value 1 Event: time 1262304222.998060, -------------- SYN_REPORT ------------ Event: time 1262304223.162092, type 1 (EV_KEY), code 102 (KEY_HOME), value 0 Event: time 1262304223.162092, -------------- SYN_REPORT ------------ Event: time 1262304223.533178, type 1 (EV_KEY), code 28 (KEY_ENTER), value 1 Event: time 1262304223.533178, -------------- SYN_REPORT ------------ Event: time 1262304223.697226, type 1 (EV_KEY), code 28 (KEY_ENTER), value 0 Event: time 1262304223.697226, -------------- SYN_REPORT ------------ Event: time 1262304224.622976, type 1 (EV_KEY), code 139 (KEY_MENU), value 1 Event: time 1262304224.622976, -------------- SYN_REPORT ------------ Event: time 1262304224.923742, type 1 (EV_KEY), code 139 (KEY_MENU), value 0 Event: time 1262304224.923742, -------------- SYN_REPORT ------------ Event: time 1262304225.818243, type 1 (EV_KEY), code 114 (KEY_VOLUMEDOWN), value 1 Event: time 1262304225.818243, -------------- SYN_REPORT ------------ Event: time 1262304226.083851, type 1 (EV_KEY), code 114 (KEY_VOLUMEDOWN), value 0 Event: time 1262304226.083851, -------------- SYN_REPORT ------------ Event: time 1262304227.911909, type 1 (EV_KEY), code 115 (KEY_VOLUMEUP), value 1 Event: time 1262304227.911909, -------------- SYN_REPORT ------------ Event: time 1262304228.165801, type 1 (EV_KEY), code 115 (KEY_VOLUMEUP), value 0 Event: time 1262304228.165801, -------------- SYN_REPORT ------------
测试结果
当发生按键时,evtest 会输出相应的信息。
串口测试(RS232)
【测试说明】:采用串口自发自收的方式进行测试
【接口标识】:UART
【系统设备】:/dev/ttyS4
测试操作
短接串口4的发送发接收管脚(RS232的TX和RX管脚)
执行测试指令:
=====> 输入指令: serial_test /dev/ttyS4 "www.myzr.com.cn" =====> 输出信息: Starting send data...finish Starting receive data: ASCII: 0x77 Character: w ASCII: 0x77 Character: w ASCII: 0x77 Character: w ASCII: 0x2e Character: . ASCII: 0x6d Character: m ASCII: 0x79 Character: y ASCII: 0x7a Character: z ASCII: 0x72 Character: r ASCII: 0x2e Character: . ASCII: 0x63 Character: c ASCII: 0x6f Character: o ASCII: 0x6d Character: m ASCII: 0x2e Character: . ASCII: 0x63 Character: c ASCII: 0x6e Character: n ASCII: 0x0 Character:
串口测试(RS485)
【测试说明】:采用串口自发自收的方式进行测试
【接口标识】:UART
【系统设备】:/dev/ttyS5/7
测试操作
短接串口5的发送管脚与串口7的接收管脚(485-1的TX和485-2的RX管脚)
短接串口7的发送管脚与串口5的接收管脚(485-2的TX和485-1的RX管脚)
执行测试指令:
=====> 输入指令: cat /dev/ttyS5 & echo www.myzr.com.cn > /dev/ttyS7 =====> 输出信息: www.myzr.com.cn =====> 输入指令: killall cat cat /dev/ttyS7 & echo www.myzr.com.cn > /dev/ttyS5 =====> 输出信息: www.myzr.com.cn
RTC 测试
【测试说明】:读取并设置时间,断电重启后检查时间是否正确
【接口标识】:无
【系统设备】:/sys/class/rtc/
测试操作
1. 断电重启设备,查看当前系统时间和硬件时间:
=====> 输入指令: date =====> 输出信息: Fri Jan 1 08:00:29 CST 2010
2. 查看当前RTC芯片时钟:
=====> 输入指令: hwclock =====> 输出信息: Fri Jan 1 00:00:41 2010 0.000000 seconds
3. 设置系统时钟,并同步到RTC芯片
=====> 输入指令: date -s "2021-05-14 12:34:56" =====> 输出信息: Fri May 14 12:34:59 CST 2021
4. 将系统时钟写入硬件时钟
=====> 输入指令: hwclock -w
测试结果
1. 断电重启评估板,查看当前系统时钟和硬件时钟
=====> 输入指令: date =====> 输出信息: Fri May 14 12:35:34 2021 0.000000 seconds
2. 查看当前RTC芯片时钟
=====> 输入指令: hwclock =====> 输出信息: Fri May 14 12:35:37 2021 0.000000 seconds
可以看到我们得到的时间与设置的时间基本相同。
音频播放测试
【测试说明】:通过播放音频文件验证评估板的音频播放功能。
测试操作
把耳机插入开发板的音频口。
执行测试命令:
=====> 输入指令: aplay /test/test.wav =====> 输出信息: Playing WAVE 'test.wav' : Signed 16 bit Little Endian, Rate 16000 Hz, Mono
测试结果
执行上面的测试命令后会听到音频设备输出的声音
音频录音测试
【测试说明】:通过录音并播放录音文件验证评估板的音频录音功能。
【接口标识】:MIC
测试操作
执行测试命令:
=====> 输入指令: arecord -d 5 -f S16_LE -t wav foobar.wav =====> 输出信息: Recording WAVE 'foobar.wav' : Signed 16 bit Little Endian, Rate 8000 Hz, Mono
播放录音:
=====> 输入指令: aplay foobar.wav =====> 输出信息: Playing WAVE 'foobar.wav' : Signed 16 bit Little Endian, Rate 8000 Hz, Mono
测试结果
执行上面的测试命令后会听到播放的录音。
显示测试
【测试说明】:执行显示程序。
【接口标识】:lvds/lcd/dsi
【系统设备】:fb0
测试操作
- 关机后接上显示屏
- 执行命令
df_andi
WIFI测试
【测试说明】:使用RTL8723du作为无线网卡连接到WIFI AP。
【接口标识】:WIFI、WIFI_ANT
【系统设备】:wlan0
测试操作
- 确定“WIFI”标识处有贴上WIFI模块,否则无需进行测试。
- 把WIFI天线连接到“WIFI_ANT”标识的接口上。
=====> 输入指令: wifi_connect_ap_test MYZR-WIFI myzr2012
MYZR-WIFI为WIFI名 myzr2012为密码
测试连接
=====> 输入指令: ping -I wlan0 www.baidu.com -c 2 -w 4 =====> 输出信息: PING www.baidu.com (163.177.151.109): 56 data bytes 64 bytes from 163.177.151.109: seq=0 ttl=56 time=9.776 ms 64 bytes from 163.177.151.109: seq=1 ttl=56 time=9.620 ms --- www.baidu.com ping statistics --- 2 packets transmitted, 2 packets received, 0% packet loss round-trip min/avg/max = 9.620/9.698/9.776 ms
测试结果
“0% packet loss”表示WIFI连接正常。
蓝牙测试
【测试说明】:扫描到蓝牙设备后,发送L2CAP回应请求并接收回答。
【系统设备】:hci0
- 确定“WIFI”标识处有贴上WIFI模块,否则无需进行测试。
- 把WIFI天线连接到“WIFI_ANT”标识的接口上。
配置蓝牙系统接口
=====> 输入指令: hciconfig hci0 up hciconfig hci0 piscan hciconfig -a
hci0: Type: BR/EDR Bus: USB BD Address: 74:EE:2A:45:64:EC ACL MTU: 1021:8 SCO MTU: 255:12 UP RUNNING PSCAN ISCAN RX bytes:1403 acl:0 sco:0 events:59 errors:0 TX bytes:786 acl:0 sco:0 commands:59 errors:0 Features: 0xff 0xff 0xff 0xfa 0xdb 0xbd 0x7b 0x87 Packet type: DM1 DM3 DM5 DH1 DH3 DH5 HV1 HV2 HV3 Link policy: RSWITCH HOLD SNIFF PARK Link mode: SLAVE ACCEPT Name: 'RTK_BT_4.1' Class: 0x000000 Service Class[ 54.305172] rtk_btcoex: BTCOEX hci_rev 0x82a8 es: Unspecified Device Class: [ 54.311358] rtk_btcoex: BTCOEX lmp_subver 0x2df4 Miscellaneous, HCI Version: 4.1 (0x7) Revision: 0x82a8 LMP Version: 4.1 (0x7) Subversion: 0x2df4 Manufacturer: Realtek Semiconductor Corporation (93)
- 查看板子蓝牙设备信息
=====> 输入指令:
hcitool dev
=====> 输出信息:
Devices: hci0 74:EE:2A:45:64:EC
5. 扫描外部蓝牙设备
=====> 输入指令:
hcitool scan
=====> 输出信息:
Scanning ... ...... 7C:2A:DB:08:EF:70 Redmi K30 Pro
- 发送发送L2CAP包测试
=====> 输入指令:
l2ping 7C:2A:DB:08:EF:70 -c 2
=====> 输出信息:
Ping: 7C:2A:DB:08:EF:70 from 74:EE:2A:45:64:EC (data size 44) ... 44 bytes from 7C:2A:DB:08:EF:70 id 0 time 7.89ms 44 bytes from 7C:2A:DB:08:EF:70 id 1 time 24.88ms 44 bytes from 7C:2A:DB:08:EF:70 id 2 time 9.80ms ^C3 sent, 3 received, 0% loss
测试结果
“0% packet loss”表示蓝牙连接正常
EC20 模块测试
【测试说明】:4G连接成功后,开发板向外网发送ICMP报文来验证连接正常。
【系统设备】:usb0
测试操作
1. 开发板断电,接上4G模块,接上天线并插入SIM卡后启动评估板。
2. 使用指令进行网络连接:
=====> 输入指令:
/etc/quectel-CM
测试连接:
=====> 输入指令:
ping www.baidu.com -c 2 -w 4
=====> 输出信息:
PING www.a.shifen.com (183.232.231.172) from 10.77.19.81 ppp0: 56(84) bytes of data. 64 bytes from 183.232.231.172: icmp_seq=1 ttl=56 time=197 ms --- www.a.shifen.com ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 197.497/197.497/197.497/0.000 ms
测试结果
“0% packet loss”表示WIFI连接正常。