MYZR-IMX6-EK140P Linux-4.1.15 测试手册

来自明远智睿的wiki
Admin（讨论 | 贡献）2018年9月21日 (五) 14:22的版本 （创建页面，内容为“ [^_^]: MY-IMX6-EK140P Linux-4.1.15 测试手册 <br /> ### 测试环境 * 开发板型号：MYIMX6140P-6Y-512M-4G * 内核版本：Linux-4.1.15...”）

(差异) ←上一版本 | 最后版本 (差异) | 下一版本→ (差异)
跳转至： 导航、 搜索


测试环境

  • 开发板型号：MYIMX6140P-6Y-512M-4G
  • 内核版本：Linux-4.1.15
  • 文件系统：L4115-core-image-base-myimx6a7.tar.bz2


网口测试

ETH0 测试
  • 关闭 ETH1 
# ifconfig eth1 down
  • 配置 ETH0 
# ifconfig eth0 192.168.137.81
  • 使用 ping 进行测试 
# ping 192.168.137.99 -c 2 -w 4  
  
PING 192.168.137.99 (192.168.137.99): 56 data bytes  
64 bytes from 192.168.137.99: seq=0 ttl=128 time=0.838 ms  
64 bytes from 192.168.137.99: seq=1 ttl=128 time=0.449 ms  
  
--- 192.168.137.99 ping statistics ---  
2 packets transmitted, 2 packets received, 0% packet loss  
round-trip min/avg/max = 0.449/0.643/0.838 ms
ETH1 测试
  • 关闭 ETH0 
# ifconfig eth0 down
  • 配置 ETH0 
# ifconfig eth1 192.168.137.82
  • 使用 ping 进行测试 
# ping 192.168.137.99 -c 2 -w 4  
  
PING 192.168.137.99 (192.168.137.99): 56 data bytes  
64 bytes from 192.168.137.99: seq=0 ttl=128 time=0.999 ms  
64 bytes from 192.168.137.99: seq=1 ttl=128 time=0.503 ms  
  
--- 192.168.137.99 ping statistics ---  
2 packets transmitted, 2 packets received, 0% packet loss  
round-trip min/avg/max = 0.503/0.751/0.999 ms

USB 测试

  • 插入U盘 
usb 1-1.4: new high-speed USB device number 4 using ci_hdrc  
usb-storage 1-1.4:1.0: USB Mass Storage device detected  
scsi host0: usb-storage 1-1.4:1.0  
scsi 0:0:0:0: Direct-Access     Mass     Storage Device   1.00 PQ: 0 ANSI: 0 CCS  
sd 0:0:0:0: [sda] 7716864 512-byte logical blocks: (3.95 GB/3.67 GiB)  
sd 0:0:0:0: [sda] Write Protect is off  
sd 0:0:0:0: [sda] No Caching mode page found  
sd 0:0:0:0: [sda] Assuming drive cache: write through  
 sda: sda1 sda2  
sd 0:0:0:0: [sda] Attached SCSI removable disk
  • 拔出U盘 
usb 1-1.4: USB disconnect, device number 4

TF卡测试

  • 查看内核输入的信息 
# dmesg | grep mmc0  
  
mmc0: SDHCI controller on 2190000.usdhc [2190000.usdhc] using ADMA  
mmc0: host does not support reading read-only switch, assuming write-enable  
mmc0: new high speed SDHC card at address 1234  
mmcblk0: mmc0:1234 SA04G 3.67 GiB
  • 查看系统的TF卡设备 
# ls /dev/mmcblk0*  
  
/dev/mmcblk0    /dev/mmcblk0p1  /dev/mmcblk0p2

标准 GPIO 测试

  • 配置 P21:36 为输出 
# OUT_IO_OUT_NUM=4  
# echo ${OUT_IO_OUT_NUM} > /sys/class/gpio/export  
# echo "out" > /sys/class/gpio/gpio${OUT_IO_OUT_NUM}/direction  
# echo 0 > /sys/class/gpio/gpio${OUT_IO_OUT_NUM}/value
  • 配置 P21:35 为输入 
# OUT_IO_IN_NUM=3  
# echo ${OUT_IO_IN_NUM} > /sys/class/gpio/export  
# echo "in" > /sys/class/gpio/gpio${OUT_IO_IN_NUM}/direction
  • 短接 P21: 35,36
  • 配置 P21:36 输出高电平并通过 P21:35 读取输入电平状态 
# echo 1 > /sys/class/gpio/gpio${OUT_IO_OUT_NUM}/value  
# cat /sys/class/gpio/gpio${OUT_IO_IN_NUM}/value
  • 配置 P21:36 输出低电平并通过 P21:35 读取输入电平状态 
# echo 0 > /sys/class/gpio/gpio${OUT_IO_OUT_NUM}/value  
# cat /sys/class/gpio/gpio${OUT_IO_IN_NUM}/value
  • 其它可用GPIO：P21:33,34,23；对应的 Number 为：2,1,110

GPIO-LED 测试

led-heartbeat
  • led-heartbeat 连接到 D11，系统启动后可以看到 D11 在有规律的闪烁。
led-timer
  • led-timer 连接到 D12，系统启动后可以看到 D12 在有规律的闪烁。
  • 更改灭的时间 
# echo 1000 > /sys/class/leds/led-timer/delay_off
  • 更改亮的时间 
# echo 2000 > /sys/class/leds/led-timer/delay_on
led-default
  • led-default 连接到 D8，系统启动后默认状态为常亮。
  • 使 D8 灭 
echo 0 > /sys/class/leds/default/brightness
  • 使 D8 常亮 
echo 1 > /sys/class/leds/default/brightness

串口测试

UART2
  • 位置：P21:27,28
  • 设备：/dev/ttymxc1
  • 测试指令 
# /my-demo/linux-4.1.15/uart_test.out /dev/ttymxc1 "www.myzr.com.cn"  
  
Welcome to TTYtest  
  
Send test data------www.myzr.com.cn  
read char is w   
read char is w   
read char is w   
read char is .   
read char is m   
read char is y   
read char is z   
read char is r   
read char is .   
read char is c   
read char is o   
read char is m   
read char is .   
read char is c   
read char is n   
Read Test Data finished,Read Test Data is-------www.myzr.com.cn
UART3
  • 位置：P21: 25,26
  • 设备：/dev/ttymxc2
  • 测试指令 
# /my-demo/linux-4.1.15/uart_test.out /dev/ttymxc2 "www.myzr.com.cn"  
  
Welcome to TTYtest  
  
Send test data------www.myzr.com.cn  
read char is w   
read char is w   
read char is w   
read char is .   
read char is m   
read char is y   
read char is z   
read char is r   
read char is .   
read char is c   
read char is o   
read char is m   
read char is .   
read char is c   
read char is n   
Read Test Data finished,Read Test Data is-------www.myzr.com.cn

CAN 测试

  • 测试准备
    将CAN1的CAN_L与CAN2的CAN_L连接；将CAN1的CAN_H与CAN2的CAN_H连接。
  • 配置 CAN1 (can0) 
# ip link set can0 up type can bitrate 125000
  • 配置 CAN2 (can1) 
# ip link set can1 up type can bitrate 125000
  • CAN1 (can0) 后台接收 
# candump can0 &
  • CAN2 (can1) 发送数据 
# cansend can1 1F334455#1122334455667788

SPI测试

ECSPI1 测试
  • 位置：P21: 3,4
  • 测试设备：/dev/spidev0.0
  • 测试指令 
# /my-demo/linux-4.1.15/spidev_test.out -D /dev/spidev0.0   
  
spi mode: 0  
bits per word: 8  
max speed: 500000 Hz (500 KHz)  
  
FF FF FF FF FF FF   
40 00 00 00 00 95   
FF FF FF FF FF FF   
FF FF FF FF FF FF   
FF FF FF FF FF FF   
DE AD BE EF BA AD   
F0 0D
ECSPI2 测试
  • 位置：P21: 9,10
  • 测试设备：/dev/spidev1.0
  • 测试指令 
# /my-demo/linux-4.1.15/spidev_test.out -D /dev/spidev1.0   
  
spi mode: 0  
bits per word: 8  
max speed: 500000 Hz (500 KHz)  
  
FF FF FF FF FF FF   
40 00 00 00 00 95   
FF FF FF FF FF FF   
FF FF FF FF FF FF   
FF FF FF FF FF FF   
DE AD BE EF BA AD   
F0 0D

Watchdog 测试

超时复位测试
# /unit_tests/wdt_driver_test.out 10 15 1  
  
Starting wdt_driver (timeout: 10, sleep: 15, test: write)  
Trying to set timeout value=10 seconds  
The actual timeout was set to 10 seconds  
Now reading back -- The timeout is 10 seconds  
  
  
U-Boot 2016.03-svn246 (Sep 11 2018 - 16:45:21 +0800)  
  
CPU:   Freescale i.MX6ULL rev1.0 528 MHz (running at 396 MHz)  
CPU:   Industrial temperature grade (-40C to 105C) at 49C  
Reset cause: WDOG  
Board: MYIMX6EK140P-6Y
喂狗测试
# /unit_tests/wdt_driver_test.out 4 2 1 &  
  
[1] 603  
root@myimx6ek140p:~# Starting wdt_driver (timeout: 4, sleep: 2, test: write)  
Trying to set timeout value=4 seconds  
The actual timeout was set to 4 seconds  
Now reading back -- The timeout is 4 seconds

RTC 测试

  • 查看当前系统时钟 
# date  
  
Wed Sep 19 14:57:13 UTC 2018
  • 查看当前RTC芯片时钟 
# hwclock   
  
Wed Sep 19 14:58:36 2018  0.000000 seconds
  • 设置系统时钟，并同步到RTC芯片 
# date -s "2018-09-21 12:34:56"  
  
Fri Sep 21 12:34:56 UTC 2018
  • 将系统时钟写入硬件时钟 
# hwclock -w
  • 断电重启评估板
  • 查看当前系统时钟
# date  
  
Fri Sep 21 12:36:11 UTC 2018
  • 查看当前RTC芯片时钟 
# hwclock  
  
Fri Sep 21 12:36:16 2018  0.000000 seconds

音频测试

播放音频
# aplay /unit_tests/audio8k16S.wav   
  
Playing WAVE '/unit_tests/audio8k16S.wav' : Signed 16 bit Little Endian, Rate 8000 Hz, Stereo
音频录音
  • 录音
# arecord -d 5 -f S16_LE -t wav foobar.wav
  • 播放录音
# aplay foobar.wav

显示屏(选配)测试

在系统启动过程中，可以看到 Linux 小企鹅和 OpenEmbedded 启动画面。

FXLS8471(选配)测试

  • 使传感器 Enable 
# echo 1 > /sys/class/misc/FreescaleAccelerometer/enable
  • 查看传感器数据 
# cat /sys/class/misc/FreescaleAccelerometer/data

MAG3110(选配)测试

  • 使传感器 Enalbe 
# echo 1 > /sys/class/misc/FreescaleGyroscope/enable
  • 测试 
# evtest

FXAS2100(选配)测试

  • 测试 
# evtest  



--------------------------------------------------------------------------------  
* Looking forward to communicating with you for more functions and field applications.  
* 珠海明远智睿科技有限公司    
* ZhuHai MYZR Technology CO.,LTD.  
* Latest Update: 2018/09/21    
--------------------------------------------------------------------------------
取自“http://wiki.myzr.com.cn/index.php?title=MYZR-IMX6-EK140P_Linux-4.1.15_测试手册&oldid=2351”