查看“MYZR-IMX6-EK200 Android511 Test”的源代码
←
MYZR-IMX6-EK200 Android511 Test
跳转至:
导航
、
搜索
因为以下原因,您没有权限编辑本页:
您所请求的操作仅限于该用户组的用户使用:
用户
您可以查看与复制此页面的源代码。
= '''1 适用范围(applicable scope)''' = [[文件:Android test 1.jpg|640px]]<br> = '''测试项目(test project)''' = == '''UART测试(UART test)''' == === '''测试说明(test instruction)''' === (1)总共有4个串口,测试程序默认选择Uart2,可以根据需要选择其他串口。<br> <span style="background:#CCCCCC">total 4 serial interfaces,defaulted Uart2 by test program,but you can choose other interface as per what is needed。</span><br> (2)测试之前需要短接串口的收发管脚,不同的开发板短接的管脚有所不同,对应关系如下图:<br> <span style="background:#CCCCCC">need to shorten send&receive pins of interface before test,pins shortened are different among different development boards,correspondence as below :</span><br> [[文件:Android test 2.1.1.jpg|640px]]<br> (3)这里选择默认配置,即Uart2,短接其对应的管脚。<br> <span style="background:#CCCCCC">here choose defaulted configuration,i.e Uart2,shorten the according pins。</span><br> === '''测试方法(test method)''' === (1)点击“Uart”按钮,启动测试程序。<br> <span style="background:#CCCCCC">click“Uart”button,to boot test program。</span><br> [[文件:Android test 2.1.2.jpg|640px]]<br> (2)点击“OpenDev”打开设备。<br> <span style="background:#CCCCCC">click“OpenDev”to open device。</span><br> (3)点击“send”发送数据。<br> <span style="background:#CCCCCC">click“send”to send data。</span><br> 如果成功收到数据,文本框会在右边显示出来,说明测试成功,如下图:<br> <span style="background:#CCCCCC">if there is a successful receiving of data,texbox will be popuped on the right side,i.e.a success of test,as below:</span><br> [[文件:Android test 2.1.2 2.jpg|640px]]<br> 如果没有收到数据,则测试失败,请检查Uart管脚是否短接,错误如下图:<br> <span style="background:#CCCCCC">if not receiving of data,that means a failure of test, please check out whether pins were shortened, errors as below:</span><br> [[文件:Android test 2.1.2 3.jpg|640px]]<br> (5)测试完成,点击关闭,退出串口测试。<br> <span style="background:#CCCCCC">when test is finished,click close,to exit the test of serial interface。</span><br> == '''SPI测试(SPI test)''' == === '''测试说明(test instruction)''' === (1)测试之前需要短接SPI的管脚,不同的开发板短接的管脚有所不同,对应关系如下:<br> <span style="background:#CCCCCC">need to shorten SPI pins before test,pins shortened are different among different development boards,correspondence as below:</span><br> [[文件:Android test 2.2.1.jpg|640px]]<br> (2)EK200与测试程序对应的是SPI2;EK314与测试程序对应的是SPI1;根据实际情况短接相应的管脚。<br> <span style="background:#CCCCCC">EK200 match up with test program by SPI2;EK314 match up with test program by SPI1;so need to shorten pins according to actual condition。</span><br> === '''2.2.2测试方法(2.2.2 test method)''' === (1)点击“SPI”按钮,启动测试程序。<br> <span style="background:#CCCCCC">click“SPI”button,to boot test program。</span><br> [[文件:Android test 2.2.2.jpg|640px]]<br> (2)点击“OpenDev”打开设备。<br> <span style="background:#CCCCCC">click“OpenDev”to open device。</span><br> (3)点击“send”发送数据。如果成功收到数据,文本框会在右边的显示出来,说明测试成功,如下图:<br> <span style="background:#CCCCCC">click“send”to send data。if there is a successful receiving of data,texbox will be popuped on the right side,i.e.a success of test,as below:</span><br> [[文件:Android test 2.2.2 2.jpg|640px]]<br> 如果没有收到数据,则测试失败,请检查管脚是否短接,错误如下图:<br> <span style="background:#CCCCCC">if not receiving of data,that means a failure of test, please check out whether pins were shortened, errors as below:</span><br> [[文件:Android test 2.2.2 3.jpg|640px]]<br> (4)测试完成,点击关闭,退出测试程序。<br> <span style="background:#CCCCCC">when test is finished,click close,to exit the test program。</span><br> == '''I2C测试(I2C test)''' == === '''测试说明(test instruction)''' === 评估板总共有3条IIC总线,每条总线都有设备,测试程序仅仅是列出每条总线的设备而已,其他不做测试。<br> <span style="background:#CCCCCC">there are total 3 IIC bus on evaluation board,each bus has its own device,test program only list the device for each bus,not for test。</span><br> === '''测试方法(test method)''' === (1)点击“I2C”按钮,启动测试程序。<br> <span style="background:#CCCCCC">click“I2C”button,to boot test program。</span><br> [[文件:Android test 2.3.2.jpg|640px]]<br> (2)点击“ListI2C”,列出所有I2C总线,总共3条,如下图:<br> <span style="background:#CCCCCC">click“ListI2C”,to list all I2C bus,total 3 units,the following figure:</span><br> [[文件:Android test 2.3.2 2.jpg|640px]]<br> (3)点击“ListDevice”列出其中一条总线上的所有设备,默认是i2c-0,如下图:<br> <span style="background:#CCCCCC">click“ListDevice”to list all devices on one of the bus,default is i2c-0,as below:</span><br> [[文件:Android test 2.2.2 3.jpg|640px]]<br> (4)点击右边的下拉菜单,分别列出另外两条总线上的设备,如下图:<br> <span style="background:#CCCCCC">click drop-down manu on right,to get separate list of devices on the other two bus,example:</span><br> [[文件:Android test 2.2.2 4.jpg|640px]]<br> [[文件:Android test 2.2.2 5.jpg|640px]]<br> (5)测试完成,退出测试。<br> <span style="background:#CCCCCC">finish test,exit test。</span><br> == '''CAN测试(CAN test)''' == === '''测试说明(test instruciton)''' === 测试之前需要连接CAN的管脚,将CAN1的CAN_L和CAN2的CAN_L连接,将CAN1的CAN_H和CAN2的CAN_H连接。<br> <span style="background:#CCCCCC">need to connect CAN pins before test,connect CAN_L of CAN1 with CAN_L of CAN2,connect CAN_H of CAN1 with CAN_H CAN2。</span><br> === '''测试方法(test method)''' === (1)点击“CAN”按钮,启动测试程序<br> <span style="background:#CCCCCC">click“CAN”button,to boot test program</span><br> [[文件:Android test 2.4.2 .jpg|640px]]<br> (2)点击“OpenDev”打开设备,点击“Send”,发送数据,如果成功接收到数据,文本框会在右边显示出来,如下图:)<br> <span style="background:#CCCCCC">click“OpenDev”to open device,click“Send”to send data,if there is a successful receiving of data,texbox will be popuped on the right side,as below:</span><br> [[文件:Android test 2.4.2 2.jpg|640px]]<br> 如果没有收到数据,则测试失败,请检查CAN的管脚是否短接,错误如下图:<br> <span style="background:#CCCCCC">if not receiving of data,that means a failure of test, please check out whether CAN pins were shortened,errors as below:</span><br> [[文件:Android test 2.4.2 3.jpg|640px]]<br> (3)测试完成,退出CAN测试。<br> <span style="background:#CCCCCC">test is over,exit CAN test。</span><br> == '''USB&SD测试(USB&SD test)''' == === '''测试说明(test instruction)''' === (1)检测USB和SD读写是否正常。<br> <span style="background:#CCCCCC">check out whether USB and SD read & write is normal or not。</span><br> === '''测试方法(test method)''' === (1)点击“SD/U盘”按钮,启动测试程序。<br> <span style="background:#CCCCCC">click“SD/U disk”button,to boot test program。</span><br> [[文件:Android test 2.4.5.jpg|640px]]<br> (2)插入U盘或者SD卡,点击“SD”或“U盘”按钮读出SD卡或U盘的内容。<br> <span style="background:#CCCCCC">insert U disk or SD card,click“SD”or“U disk”button to read out the content of SD card or U disk。</span><br> [[文件:Android test 2.4.5 2.jpg|640px]]<br> (3)测试完成,退出测试程序<br> <span style="background:#CCCCCC">test is over,exit test program</span><br> == '''WIFI&网口测试(WIFI& lan port test)''' == === '''测试说明(test instruction)''' === 检测WIFI与网口功能。<br> <span style="background:#CCCCCC">check out function of WIFI and lan port。</span><br> === '''WIFI测试方法(WIFI test method)''' === (1)点击“WIFI按钮”,启动测试程序。<br> <span style="background:#CCCCCC">click“WIFI button”,to boot test program。</span><br> [[文件:Android test 2.6.2.jpg|640px]]<br> (2)点击“wifi”开关,打开wifi后点击“search”搜索wifi.<br> <span style="background:#CCCCCC">click“wifi”switch,after open wifi then click“search”to search wifi.</span><br> [[文件:Android test 2.6.2 2.jpg|640px]]<br> (3)点击要连接的Wifi,输入密码进行连接。<br> <span style="background:#CCCCCC">click Wifi which will be linked,enter password for the link。</span><br> (4)连接成功后点击“Link”按钮连接百度。<br> <span style="background:#CCCCCC">if a successful link,then click“Link”to link with baidu。</span><br> (5)若连接失败检查网络是否畅顺。<br> <span style="background:#CCCCCC">if failure of link,please check out whether network is working。</span><br> === '''网口测试方法(lan port test method)''' === (1)将能正常上网的网线连接到网口<br> <span style="background:#CCCCCC">connect lan cable with lan port</span><br> (2)点击“Intent”按钮连接百度<br> <span style="background:#CCCCCC">click“Intent”button to link to baidu</span><br> == '''多媒体测试(multi media test)''' == === '''测试说明(test instruction)''' === (1)测试音频和视频的功能。<br> <span style="background:#CCCCCC">test functions of audio and vedio。</span> === '''测试方法(test method)''' === (1)点击“Audio/video”按钮,启动测试程序。<br> <span style="background:#CCCCCC">click“Audio/video”button,to boot test program。</span><br> [[文件:Android test 2.7.2.jpg|640px]]<br> (2)插上耳机,点击“Play_music”,可以听到一段音乐。<br> <span style="background:#CCCCCC">wear earphone,click“Play_music”,can hear a piece of music。</span><br> (3)点击“Play_video”,播放一段视频。<br> <span style="background:#CCCCCC">click“Play_video”,to play a piece of vedio。</span><br> [[文件:Android test 2.7.2 2.jpg|640px]]<br> (4)测试完成,退出测试程序。<br> <span style="background:#CCCCCC">test is over,exit test program。</span><br> == '''产品介绍(product instroduction)''' == === '''产品图片(product photo)''' === (1)点击“Product”按钮,可以看到我司产品图片介绍,左右滑动屏幕能了解更多。<br> <span style="background:#CCCCCC">click“Product”button,you can see the instruduction and photo of our products,left or right sliding screen for more information。</span><br> [[文件:Android test 2.8.1.png|640px]]<br>
返回至
MYZR-IMX6-EK200 Android511 Test
。
导航菜单
个人工具
登录
命名空间
页面
讨论
变种
视图
阅读
查看源代码
查看历史
更多
搜索
[-_-]
NXP平台:
MYZR-IMX6-EK200
MYZR-IMX6-EK200(EN)
MYZR-IMX6-EK314
MYZR-IMX6-EK314(EN)
MYZR-IMX6-EK336
MYZR-IMX6-EK336(EN)
MYZR-IMX6-EK140
MYZR-IMX6-EK140(EN)
MYZR-IMX6-EK140P
MYZR-IMX6-EK140P(EN)
MYZR-IMX8M-EK300
MYZR-IMX8M-EK300(EN)
MYZR-IMX8M-EVK
MYZR-IMX8Mmini-EK240
MYZR-IMX8Mmini-EK240(EN)
MYZR-IMX28-EK142
MYZR-IMX28-EK142(EN)
MYZR-LS1012A-EK200
MYZR-LS1012A-EK200(EN)
Rockchip平台:
MYZR-RK3288-EK314
MYZR-RK3288-EK314(EN)
MYZR-RK3399-EK314
MYZR-RK3399-EK314(EN)
Allwinner平台:
MYZR-R16-EK166
MYZR-R16-EK166(EN)
Microchip平台:
MYZR-SAMA5-EK200
MYZR-SAMA5-EK200(EN)
网关产品:
GW200
GW300
GW310/GW311
ST平台:
MYZR-STM32-EK152
所有页面
工具
链入页面
相关更改
特殊页面
页面信息