“MYZR-IMX6-EK314 Linux-4.1.15 Test Manual v2.0”的版本间的差异

来自明远智睿的wiki
跳转至: 导航搜索
(创建页面,内容为“ [^_^]: MY-IMX6-EK314 Linux-3.14.52 Test manual v2.0 <br> ## **Part I :Testing Instructions** ### Test Environment   【Development board model】...”)
 
 
(未显示同一用户的2个中间版本)
第7行: 第7行:
  
 
### Test Environment
 
### Test Environment
  【Development board model】:MY-IMX6-EK314-6Q-1G   
+
  【Development board model】:MYZR-IMX6-EK314-6Q-1G   
 
  【Kernel version】:Linux-4.1.15   
 
  【Kernel version】:Linux-4.1.15   
 
  【File system】:L4115-fsl-image-qt5-myimx6a9.tar.bz2     
 
  【File system】:L4115-fsl-image-qt5-myimx6a9.tar.bz2     
第15行: 第15行:
  
 
### Interface identification map
 
### Interface identification map
[[File:My-imx6ek314 front.jpg|642px]]   
+
[[File:My-imx6ek314 front.jpg|850px]]   
[[File:My-imx6ek314 back.jpg|642px]]   
+
[[File:My-imx6ek314 back.jpg|850px]]   
 
<br>
 
<br>
  
第135行: 第135行:
 
  【Interface identifier】:GPIO   
 
  【Interface identifier】:GPIO   
 
  【System interface】:/sys/class/gpio/   
 
  【System interface】:/sys/class/gpio/   
**IO available for MY-IMX6-EK314**   
+
**IO available for MYZR-IMX6-EK314**   
 
<pre>
 
<pre>
 
U14:3(193), U14:5(177), U14:7(176), U14:9(35), U14:11(169), U14:13(34), U14:15(36), U14:17(29)
 
U14:3(193), U14:5(177), U14:7(176), U14:9(35), U14:11(169), U14:13(34), U14:15(36), U14:17(29)

2020年10月22日 (四) 14:09的最新版本

Part I :Testing Instructions

Test Environment

  【Development board model】:MYZR-IMX6-EK314-6Q-1G
  【Kernel version】:Linux-4.1.15
  【File system】:L4115-fsl-image-qt5-myimx6a9.tar.bz2
  【Tool version】:MfgTool-MYIMX6A9-L4.1.15-Patch.svn297.rar
  Note:In order to ensure the test is correct, the recommended version of the burning tool should be no less than svn298

Interface identification map

My-imx6ek314 front.jpg

My-imx6ek314 back.jpg


Part II Interface Testing

Network port test

  【Test instruction】:Test the way that the development board sends ICMP packets to the PC.
  【Interface identifier】:10M/100M Ethernet-1
  【System interface】:eth0
Test operation
  Configure the computer wired network card IP to 192.168.137.99.
  Connect the network port of the development board with the network cable and the computer network port.
  Configure the development board network port:

  
=====>Enter the command:
ifconfig eth1 down 
ifconfig eth0 192.168.137.81  

  Test network port:

  
=====> Enter the command:    
ping 192.168.137.99 -c 2 -w 4 

=====> Output information:  
PING 192.168.137.99 (192.168.137.99) 56(84) bytes of data.  
64 bytes from 192.168.137.99: icmp_seq=1 ttl=128 time=0.570 ms  
64 bytes from 192.168.137.99: icmp_seq=2 ttl=128 time=0.365 ms  

--- 192.168.137.99 ping statistics ---
2 packets transmitted, 2 received, 0% packet loss, time 999ms
rtt min/avg/max/mdev = 0.365/0.467/0.570/0.104 ms

Test Results
  “0% packet loss”means the test passed.

Network port two test

  【Test instruction】:Test the way that the development board sends ICMP packets to the PC.
  【Interface identifier】:10M/100M Ethernet-2
  【System interface】:eth1
Test operation
  Configure the computer wired network card IP to 192.168.137.99.
  Connect the network port of the development board with the network cable and the computer network port.
  Configure the development board network port:

=====> Enter the command:
ifconfig eth0 down
ifconfig eth1 192.168.137.82 

  Test network port:

=====> Enter the command:  
ping 192.168.137.99 -c 2 -w 4 

=====> Output information: 
PING 192.168.137.99 (192.168.137.99) 56(84) bytes of data.
64 bytes from 192.168.137.99: icmp_seq=1 ttl=128 time=1.38 ms
64 bytes from 192.168.137.99: icmp_seq=2 ttl=128 time=0.627 ms

--- 192.168.137.99 ping statistics ---
2 packets transmitted, 2 received, 0% packet loss, time 1001ms
rtt min/avg/max/mdev = 0.627/1.003/1.380/0.377 ms

Test Results
  “0% packet loss”means the test passed.

USB interface test

  【Test instruction】:Test by plugging and unplugging a USB storage device (U disk)
  【Interface identifier】:USB HOST
  【System interface】:/sys/bus/usb/
Test Methods
  Insert the USB device into the backplane USB interface and the system will output a message similar to the following:

usb 1-1.2: new high-speed USB device number 5 using ci_hdrc
usb-storage 1-1.2:1.0: USB Mass Storage device detected
scsi host1: usb-storage 1-1.2:1.0
scsi 1:0:0:0: Direct-Access     Mass     Storage Device   1.00 PQ: 0 ANSI: 0 CCS
sd 1:0:0:0: Attached scsi generic sg0 type 0
sd 1:0:0:0: [sda] 60776448 512-byte logical blocks: (31.1 GB/28.9 GiB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] No Caching mode page found
sd 1:0:0:0: [sda] Assuming drive cache: write through
 sda: sda1
sd 1:0:0:0: [sda] Attached SCSI removable disk

  Pull the USB device out of the backplane and the system will output a message similar to the following:

usb 1-1.2: USB disconnect, device number 5

Test Results
  When the USB storage device is plugged and unplugged, the system outputs the above information to indicate normal.

SD interface test

  【Test instruction】:Test by inserting and identifying a TF card
  【Interface identifier】:SD3
  【System interface】:/sys/bus/mmc/
Test Methods
  Insert the SD card into this interface:

=====> Output information:
mmc2: new high speed SDHC card at address 1234
mmcblk2: mmc2:1234 SA32G 28.9 GiB 
 mmcblk2: p1

  Pop up the SD card:

=====> Output information:  
mmc2: card 1234 removed  

Test Results
  When the SD storage device is plugged and unplugged, the system outputs the above information to indicate normal.

Standard GPIO test

  【Test instruction】:Control the output level of the GPIO
  【Interface identifier】:GPIO
  【System interface】:/sys/class/gpio/
IO available for MYZR-IMX6-EK314

U14:3(193), U14:5(177), U14:7(176), U14:9(35), U14:11(169), U14:13(34), U14:15(36), U14:17(29)
U14:4(192), U14:6(178), U14:8(39), U14:10(38), U14:12(171), U14:14(32), U14:16(37), U14:18(27)
U14:19(30), U14:21(24), U14:23(10), U14:25(12), U14:27(11), U14:29(85), U14:35(20), U14:37(116)
U14:20(26), U14:22(GND), U14:24(15), U14:26(13), U14:28(14), U14:30(86), U14:36(NC), U14:38(NC)

GPIO output low level test
  Configure U14:29 to output low level operation method:

=====> Enter the command:
OUT_IO_OUT_NUM=85
echo ${OUT_IO_OUT_NUM} > /sys/class/gpio/export    
echo "out" > /sys/class/gpio/gpio${OUT_IO_OUT_NUM}/direction  
echo 0 > /sys/class/gpio/gpio${OUT_IO_OUT_NUM}/value 

  Test the pin U14:29 with a multimeter, the voltage is 0V, it means OK
GPIO output high level test
  Configure U14:30 to output high level operation method:

=====> Enter the command:
OUT_IO_OUT_NUM=86 
echo ${OUT_IO_OUT_NUM} > /sys/class/gpio/export
echo "out" > /sys/class/gpio/gpio${OUT_IO_OUT_NUM}/direction  
echo 1 > /sys/class/gpio/gpio${OUT_IO_OUT_NUM}/value

  Test the pin U14:30 with a multimeter, the voltage is 3.3V, it means OK
Other
  Instructions to control GPIO output low level:

=====> Enter the command:  
echo 0 > /sys/class/gpio/gpio${OUT_IO_OUT_NUM}/value   

  Instructions to control GPIO output high level:

=====> Enter the command:  
echo 1 > /sys/class/gpio/gpio${OUT_IO_OUT_NUM}/value 


GPIO-LED Test(leds-heartbeat)

  【Test instruction】:Observe the leds of leds-heartbeat
  【Interface identifier】:GPIO-LED
  【System interface】:/sys/class/leds/leds-heartbeat/
Test operation
  No need for any operation.
Test Results
  After the system is started, you can see that D15 is flashing regularly, which means it should function normally.

GPIO-LED Test(leds-mmc3)

  【Test instruction】:Write data to eMMC while observing LEDs of leds-mmc3
  【Interface identifier】:GPIO-LED
  【System interface】:/sys/class/leds/leds-mmc3/
Test operation

=====>  Enter the command:  
dd if=/dev/zero of=/home/root/test bs=1024k count=128

Test Results
  You can see that when you write data to eMMC, D16 is bright.

GPIO-LED Test(leds-timer)

  【Test instruction】:Observe led-time LEDs
  【Test instruction】:Control the lighting time of led-time(LED)
  【Interface identifier】:GPIO-LED
  【System interface】:/sys/class/leds/leds-timer/
Test operation
  Change the time of led-time(D17) extinction

=====>  Enter the command:  
echo 1000 > /sys/class/leds/leds-timer/delay_off  

  Change the time that led-timer (D17) is on

=====>  Enter the command:  
echo 2000 > /sys/class/leds/leds-timer/delay_on  

Test Results
  After executing the instruction, it is observed that the proportion of time for the corresponding LED to be on and off is basically 2:1.

GPIO-LED Test(leds-gpio)

  【Test instruction】:Control the on and off time of ledss-gpio (LED)
  【Interface identifier】:LED
  【System interface】:/sys/class/leds/leds-gpio/
Test operation
  Make the light (D18) off:

=====> Enter the command:  
echo 0 > /sys/class/leds/leds-gpio/brightness  

  Turn the light(D18) on:

=====>  Enter the command:  
echo 1 > /sys/class/leds/leds-gpio/brightness  

Test Results
  After executing the instruction, it is found that the state of the corresponding LED changes with the function of the instruction.

GPIO-KEY test

  【Test instruction】:Use evtest for testing
  【Interface identifier】:KEY3, KEY2, KEY1
  【System interface】:/dev/input/eventX
Test operation
  Run evtest to prepare for testing

=====> Enter the command:  
evtest 

=====> Output information:  
No device specified, trying to scan all of /dev/input/event*
Available devices:
/dev/input/event0:  WM8962 Beep Generator
/dev/input/event1:  gpio-keys.20
Select the device event number [0-1]:

  Select the serial number corresponding to gpio-keys

=====> Enter the command:  
1

=====>Output information:  
Input driver version is 1.0.1
Input device ID: bus 0x19 vendor 0x1 product 0x1 version 0x100
Input device name: "gpio-keys"
Supported events:
  Event type 0 (EV_SYN)
  Event type 1 (EV_KEY)
    Event code 114 (KEY_VOLUMEDOWN)
    Event code 115 (KEY_VOLUMEUP)
    Event code 116 (KEY_POWER)
Properties:
Testing ... (interrupt to exit)

  Press the button on the development board

Event: time 1537921332.815219, type 1 (EV_KEY), code 114 (KEY_VOLUMEDOWN), value 1
Event: time 1537921332.815219, -------------- SYN_REPORT ------------
Event: time 1537921332.985211, type 1 (EV_KEY), code 114 (KEY_VOLUMEDOWN), value 0
Event: time 1537921332.985211, -------------- SYN_REPORT ------------
Event: time 1537921335.355204, type 1 (EV_KEY), code 115 (KEY_VOLUMEUP), value 1
Event: time 1537921335.355204, -------------- SYN_REPORT ------------
Event: time 1537921335.535203, type 1 (EV_KEY), code 115 (KEY_VOLUMEUP), value 0
Event: time 1537921335.535203, -------------- SYN_REPORT ------------
Event: time 1537921337.375207, type 1 (EV_KEY), code 116 (KEY_POWER), value 1
Event: time 1537921337.375207, -------------- SYN_REPORT ------------
Event: time 1537921337.535204, type 1 (EV_KEY), code 116 (KEY_POWER), value 0
Event: time 1537921337.535204, -------------- SYN_REPORT ------------

Test Results
  When a button is pressed, evtest will output the corresponding information.

Serial test(UART2)

  【Test instruction】:Test by serial port self-receiving
  【Interface identifier】:TTL_UART
  【System equipment】:/dev/ttymxc1
Test operation
  Short the serial port 2 transmit and receive pin (J12 pins 9 and 10)
  Execute test instructions:

=====> Enter the command:  
/my-demo/gcc-linaro-5.3-arm/serial_test.out /dev/ttymxc1 "www.myzr.com.cn"  

=====> Output information:  
Starting send data...finish
Starting receive data:
ASCII: 0x77      Character: w 
ASCII: 0x77      Character: w 
ASCII: 0x77      Character: w 
ASCII: 0x2e      Character: . 
ASCII: 0x6d      Character: m 
ASCII: 0x79      Character: y 
ASCII: 0x7a      Character: z 
ASCII: 0x72      Character: r 
ASCII: 0x2e      Character: . 
ASCII: 0x63      Character: c 
ASCII: 0x6f      Character: o 
ASCII: 0x6d      Character: m 
ASCII: 0x2e      Character: . 
ASCII: 0x63      Character: c 
ASCII: 0x6e      Character: n 
ASCII: 0x0       Character:   

Test Results
  After executing the test command, the application output is similar to the above information.

Serial test(UART3)

  【Test instruction】:Test by serial port self-receiving
  【Interface identifier】:TTL_UART
  【System equipment】:/dev/ttymxc2
Test operation
  Short-circuit the transmit and receive pins of serial port 3 (pins 12 and 13 of J12).
  Execute test instructions:

=====>  Enter the command:  
/my-demo/gcc-linaro-5.3-arm/serial_test.out /dev/ttymxc2 "www.myzr.com.cn"  

=====> Output information:  
Starting send data...finish
Starting receive data:
ASCII: 0x77      Character: w 
ASCII: 0x77      Character: w 
ASCII: 0x77      Character: w 
ASCII: 0x2e      Character: . 
ASCII: 0x6d      Character: m 
ASCII: 0x79      Character: y 
ASCII: 0x7a      Character: z 
ASCII: 0x72      Character: r 
ASCII: 0x2e      Character: . 
ASCII: 0x63      Character: c 
ASCII: 0x6f      Character: o 
ASCII: 0x6d      Character: m 
ASCII: 0x2e      Character: . 
ASCII: 0x63      Character: c 
ASCII: 0x6e      Character: n 
ASCII: 0x0       Character:   

Test Results
  After executing the test instruction, the application output similar information as above is normal.

Serial test(UART4)

  【Test instruction】:Test by serial port self-receiving
  【Interface identifier】:TTL_UART
  【System equipment】:/dev/ttymxc3
Test operation
  Short-circuit the transmit and receive pins of serial port 4 (pins 15 and 17 of J12)

   Execute test instructions:
=====>  Enter the command:
/my-demo/gcc-linaro-5.3-arm/serial_test.out /dev/ttymxc3 "www.myzr.com.cn"  

=====>  Output information:  
Starting send data...finish
Starting receive data:
ASCII: 0x77      Character: w 
ASCII: 0x77      Character: w 
ASCII: 0x77      Character: w 
ASCII: 0x2e      Character: . 
ASCII: 0x6d      Character: m 
ASCII: 0x79      Character: y 
ASCII: 0x7a      Character: z 
ASCII: 0x72      Character: r 
ASCII: 0x2e      Character: . 
ASCII: 0x63      Character: c 
ASCII: 0x6f      Character: o 
ASCII: 0x6d      Character: m 
ASCII: 0x2e      Character: . 
ASCII: 0x63      Character: c 
ASCII: 0x6e      Character: n 
ASCII: 0x0       Character:   

Test Results
  After executing the test instruction, the application output similar information as above is normal.

Serial test(UART5)

  【Test instruction】:The serial port self - collecting method was used to test
  【Interface identifier】:TTL_UART
  【System equipment】:/dev/ttymxc4
Test operation
  Short-circuit the transmit and receive pins of serial port 5 (pins 16 and 18 of J12)
  Execute test instructions:

=====> Enter the command:  
/my-demo/gcc-linaro-5.3-arm/serial_test.out /dev/ttymxc4 "www.myzr.com.cn"  

=====> Output information:  
Starting send data...finish
Starting receive data:
ASCII: 0x77      Character: w 
ASCII: 0x77      Character: w 
ASCII: 0x77      Character: w 
ASCII: 0x2e      Character: . 
ASCII: 0x6d      Character: m 
ASCII: 0x79      Character: y 
ASCII: 0x7a      Character: z 
ASCII: 0x72      Character: r 
ASCII: 0x2e      Character: . 
ASCII: 0x63      Character: c 
ASCII: 0x6f      Character: o 
ASCII: 0x6d      Character: m 
ASCII: 0x2e      Character: . 
ASCII: 0x63      Character: c 
ASCII: 0x6e      Character: n 
ASCII: 0x0       Character:   

Test Results
  After executing the test instruction, the application output similar information as above is normal.

CAN test

  【Test instruction】:CAN1 sending and CAN0 receiving are adopted.
  【Interface identifier】:CAN1,CAN2
  【System interface】:can0,can1
Test preparation
  Connect CAN_L of CAN1 to CAN_L of CAN2.
  Connect CAN_H of CAN1 to CAN_H of CAN2.
Test command
  Configure CAN1(can0):

=====> Enter the command:
ip link set can0 up type can bitrate 125000

  Configure CAN2(can1):

=====>  Enter the command:  
ip link set can1 up type can bitrate 125000

  CAN1 (can0) background reception :

=====> Enter the command:
candump can0 &  

  CAN2(can1)send data:

=====> Enter the command:  
cansend can1 1F334455#1122334455667788 

=====> Output information:  
can0  1F334455   [8]  11 22 33 44 55 66 77 88

Test Results
  After CAN2 (can1) transmits data, CAN1 (can0) will output the received data, such as: 11 22 33 44 55 66 77 88

SPI test(ECSPI1)

  【Test instruction】:Tested by spontaneous self-receiving.
  【Interface identifier】:SPI
  【System equipment】:/dev/spidev0.1
Test operation
  Short the 6 and 12 pins of J7.
  Execute test instruction

=====> Enter the command:  
/my-demo/gcc-linaro-5.3-arm/spidev_test.out -D /dev/spidev0.1   

=====> Output information: 
spi mode: 0
bits per word: 8
max speed: 500000 Hz (500 KHz)

FF FF FF FF FF FF   
40 00 00 00 00 95   
FF FF FF FF FF FF   
FF FF FF FF FF FF   
FF FF FF FF FF FF   
DE AD BE EF BA AD   
F0 0D 

Test Results
  After executing the test instruction, the application output similar information as above is normal.

SPI test(ECSPI2)

  【Test instruction】:Tested by spontaneous self-receiving.
  【Interface identifier】:SPI
  【System equipment】:/dev/spidev1.0
Test operation
  Short the 7 and 11 pins of the J13.   Execute test instructions

=====> Enter the command:  
/my-demo/gcc-linaro-5.3-arm/spidev_test.out -D /dev/spidev1.0   

=====> Output information:  
spi mode: 0
bits per word: 8
max speed: 500000 Hz (500 KHz)

FF FF FF FF FF FF   
40 00 00 00 00 95   
FF FF FF FF FF FF   
FF FF FF FF FF FF   
FF FF FF FF FF FF   
DE AD BE EF BA AD   
F0 0D

Test Results
  After Execute test instructions, the application output is similar to the above information.

Watchdog Timeout reset test

  【Test instruction】:Turn on the watchdog and wait for the watchdog to time out, generating a reset.
  【Interface identifier】:None
  【System equipment】:/dev/watchdog
Test operation
  Run the watchdog program:

=====> Enter the command: 
/unit_tests/wdt_driver_test.out 10 15 1  
  
=====> Output information:
Starting wdt_driver (timeout: 10, sleep: 15, test: write)
Trying to set timeout value=10 seconds
The actual timeout was set to 10 seconds
Now reading back -- The timeout is 10 seconds

Test Results
  After running the test command for 10 seconds, WatchDog times out and the system is reset. The information that will see the system restart output at the terminal is similar to the following:

U-Boot 2016.03-svn351 (Jan 25 2019 - 10:13:51 +0800)

CPU:   Freescale i.MX6Q rev1.5 996 MHz (running at 792 MHz)
CPU:   Extended Commercial temperature grade (-20C to 105C) at 48C
Reset cause: WDOG
Board: MYZR i.MX6 Evaluation Kit
Model: MY-IMX6-EK314-6Q-1G


Watchdog Feeding dog test

  【Test instruction】:Turn on the watchdog and feed the app to the dog.
  【Interface identifier】:None
  【System equipment】:/dev/watchdog
Test operation
  Run the watchdog program and set the timeout to 4 seconds and the dog interval to 2 seconds:

=====> Enter the command:
/unit_tests/wdt_driver_test.out 4 2 1 &  
  
=====> Output information:
[1] 1026
Starting wdt_driver (timeout: 4, sleep: 2, test: write)
Trying to set timeout value=4 seconds
The actual timeout was set to 4 seconds
Now reading back -- The timeout is 4 seconds


RTC test

  【Test instruction】:Read and set the time, check the time is correct after power off and restart
  【Interface identifier】:None
  【System equipment】:/sys/class/rtc/rtc0/
Test operation
  1.Power off and restart the device to check the current system time and hardware time:

=====> Enter the command:  
date

=====> Output information: 
Tue Sep 25 22:47:03 UTC 2018

  2. View the current RTC chip clock:

=====> Enter the command: 
hwclock 

=====> Output information:  
Tue Sep 25 22:47:18 2018  0.000000 seconds

  3. Set the system clock and sync to the RTC chip

=====>  Enter the command: 
date -s "2019-01-14 12:34:56"  

=====> Output information: 
Mon Jan 14 12:34:56 UTC 2019

  4. Write the system clock to the hardware clock

=====>  Enter the command:
hwclock -w  

Test Results
  1. Power off the evaluation board to view the current system clock and hardware clock

=====>  Enter the command:  
date

=====> Output information: 
Mon Jan 14 12:36:22 UTC 2019

  2. View the current RTC chip clock

=====> Enter the command:  
hwclock  

=====> Output information:  
Mon Jan 14 12:36:40 2019  0.000000 seconds

  It can be seen that the time we get is basically the same as the time set.

WakeAlarm Wake up test

  【Test instruction】:Set the wakealarm event, then put the system to sleep and wait for the wakealarm event to wake up.
  【Interface identifier】:None
  【System equipment】:Such as /sys/class/rtc/rtc1/wakealarm
Test operation
  1. Set rtc1 to generate a wakealarm event after 10 seconds

=====> Enter the command:
echo +10 > /sys/class/rtc/rtc1/wakealarm 

  2.Put the device to sleep

=====> Enter the command:
echo mem > /sys/power/state

=====> Output information:  
PM: Syncing filesystems ... done.
Freezing user space processes ... (elapsed 0.001 seconds) done.  
Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.  
Suspending console(s) (use no_console_suspend to debug)  

Test Results
  1. You can see that the LEDs of the development board except the power indicator are off.
  2. The state of the LED is restored again within 10 seconds, and the system outputs something like the following:

PM: suspend of devices complete after 90.667 msecs
PM: suspend devices took 0.090 seconds
PM: late suspend of devices complete after 1.286 msecs
PM: noirq suspend of devices complete after 1.272 msecs
Disabling non-boot CPUs ...
CPU1: shutdown
CPU2: shutdown
CPU3: shutdown
Enabling non-boot CPUs ...
CPU1 is up
CPU2 is up
CPU3 is up
PM: noirq resume of devices complete after 1.140 msecs
PM: early resume of devices complete after 1.114 msecs
PM: resume of devices complete after 760.379 msecs
PM: resume devices took 0.760 seconds
Restarting tasks ... done.


Audio playback test

  【Test instruction】:Verify the audio playback of the EV kit by playing an audio file.
  【Interface identifier】:EAR
  【System equipment】:wm8960-audio
Test operation
  Plug the headset into the "EAR" port of the board.
  Execute the test command:

=====> Enter the command: 
aplay /unit_tests/audio8k16S.wav   

=====> Output information:  
Playing WAVE '/unit_tests/audio8k16S.wav' : Signed 16 bit Little Endian, Rate 8000 Hz, Stereo

Test Results
  After the above test command is executed, the sound output from the audio device will be heard.

Audio recording test

  【Test instruction】:Verify the audio recording function of the EV kit by recording and playing the recording file.
  【Interface identifier】:MIC
  【System equipment】:wm8960-audio
Test operation
  1. Plug the headset with the MIC into the “MIC” port of the development board.
  2. Execute the recording command:

=====> Enter the command:  
arecord -d 5 -f S16_LE -t wav foobar.wav

=====> Output information:  
Recording WAVE 'foobar.wav' : Signed 16 bit Little Endian, Rate 8000 Hz, Mono

  3. Play recording

=====> Enter the command:
aplay foobar.wav

=====> Output information: 
Playing WAVE 'foobar.wav' : Signed 16 bit Little Endian, Rate 8000 Hz, Mono

Test Results
  The recorded recording will be heard after executing the above test command.

Part III Display function test

Operating instructions

  Each display function test needs to restart the system to enter the u-boot command line and execute the command under the u-boot command line.

Single screen display

  • LVDS1 display
    Note: The default is LVDS1 display, that is, LVDS1 is the display device when it is not intervened after power-on. Explicitly configure LVDS1 as the display method:
run load_scr; source; setenv display $disp_fb0_lvds1; saveenv; boot
  • LVDS0 display
run load_scr; source; setenv display $disp_fb0_lvds0; saveenv; boot
  • HDMI display
run load_scr; source; setenv display $disp_fb0_hdmi; saveenv; boot
  • LCD(RGB) display
run load_scr; source; setenv display $disp_fb0_lcd; saveenv; boot

Dual LVDS screen display

  • LVDS1 + LVDS0 Dual screen sync display
run load_scr; source; setenv display $disp_lvds_dul; saveenv; boot
  • LVDS1 + LVDS0(fb4) Dual screen asynchronous display
run load_scr; source; setenv display $disp_lvds_sep; saveenv; boot

Dual screen asynchronous display

  • LVDS1 + HDMI Dual screen asynchronous display
run load_scr; source; setenv display $disp_fb0_lvds1 $disp_fb1_hdmi; saveenv; boot
  • LVDS1 + LCD(RGB) Dual screen asynchronous display
run load_scr; source; setenv display $disp_fb0_lvds1 $disp_fb1_lcd; saveenv; boot
  • LVDS0 + HDMI Dual screen asynchronous display
run load_scr; source; setenv display $disp_fb0_lvds0 $disp_fb1_hdmi; saveenv; boot
  • LVDS0 + LCD(RGB) Dual screen asynchronous display
run load_scr; source; setenv display $disp_fb0_lvds0 $disp_fb1_lcd; saveenv; boot
  • HDMI + LVDS1 Dual screen asynchronous display
run load_scr; source; setenv display $disp_fb0_hdmi $disp_fb1_lvds1; saveenv; boot
  • HDMI + LVDS0 Dual screen asynchronous display
run load_scr; source; setenv display $disp_fb0_hdmi $disp_fb1_lvds0; saveenv; boot
  • LCD(RGB) + LVDS1 Dual screen asynchronous display
run load_scr; source; setenv display $disp_fb0_lcd $disp_fb1_lvds1; saveenv; boot
  • LCD(RGB) + LVDS0 Dual screen asynchronous display
run load_scr; source; setenv display $disp_fb0_lcd $disp_fb1_lvds0; saveenv; boot


Part IV Expansion Module Function Demo

RTL8188 Module function demonstration(WIFI Client)

  【Test instruction】:Connect to the WIFI AP using the RTL8188 as a wireless network card.
  【Interface identifier】:WIFI、WIFI_ANT
  【System equipment】:wlan0
Test operation
  1. Make sure that the WIFI module is attached to the “WIFI” logo, otherwise no testing is required.
  2. Connect the WIFI antenna to the interface labeled "WIFI_ANT".
  3. Generate WPA PSK file for SSID
  Command format: wpa_passphrase <ssid> [passphrase]

=====> Enter the command:
wpa_passphrase MY-TEST-AP myzr2012 > /etc/wpa_supplicant.conf
pkill wpa_supplicant

  4. connection

=====> Enter the command:  
wpa_supplicant -B -i wlan0 -c /etc/wpa_supplicant.conf

=====> Output information:  
Successfully initialized wpa_supplicant
rfkill: Cannot open RFKILL control device
==> rtl8188e_iol_efuse_patch 
IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
......

  5. Get IP

=====>  Enter the command:  
udhcpc -i wlan0

=====>  Output information:  
udhcpc (v1.23.1) started
Sending discover...
Sending select for 192.168.43.121...
Lease of 192.168.43.121 obtained, lease time 3600
/etc/udhcpc.d/50default: Adding DNS 192.168.43.1

  6. Test connection

=====>  Enter the command:  
ping -I wlan0 192.168.43.1 -c 2 -w 4

=====> Output information:  
PING 192.168.43.1 (192.168.43.1) from 192.168.43.130 wlan0: 56(84) bytes of data.
64 bytes from 192.168.43.1: icmp_seq=1 ttl=64 time=5.66 ms
64 bytes from 192.168.43.1: icmp_seq=2 ttl=64 time=9.22 ms

--- 192.168.43.1 ping statistics ---
2 packets transmitted, 2 received, 0% packet loss, time 1000ms
rtt min/avg/max/mdev = 5.663/7.444/9.226/1.783 ms

Test Results
  “0% packet loss” means WIFI connection is normal.

RTL8188 Module function demonstration(WIFI AP mode)

  【Test instruction】:Use RTL8188 as the WIFI AP and connect your phone to this AP.
  【Interface identifier】:WIFI、WIFI_ANT
  【System equipment】:wlan0
Test operation
  1. Make sure that the WIFI module is attached to the “WIFI” logo, otherwise no testing is required.
  2. Connect the WIFI antenna to the interface labeled "WIFI_ANT".
  3. Configure IP for wlan0:

=====> Enter the command: 
ifconfig wlan0 192.168.99.1

=====> Output information: 
==> rtl8188e_iol_efuse_patch
IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready

  4. Enable the DHCP service for wlan0:

=====>  Enter the command: 
touch /var/lib/misc/udhcpd.leases
udhcpd -f /etc/my_udhcpd.conf &

=====> Output information: 
[1] 469
udhcpd (v1.23.1) started

  5. Enable Host-AP feature for wlan0

=====> Enter the command: 
hostapd /etc/my_hostapd.conf -B

=====> Output information:
Configuration file: /etc/my_hostapd.conf
rfkill: Cannot open RFKILL control device
Using interface wlan0 with hwaddr e0:b9:4d:7f:e4:40 and ssid "MY_HOSTAP_V25"
RTL871X: set group key camid:1, addr:00:00:00:00:00:00, kid:1, type:AES
wlan0: interface state UNINITIALIZED->ENABLED
wlan0: AP-ENABLED

  5. Client device connected to Host-AP
  At this point, the development board's Host-AP function is enabled, the client device can search for "MY_HOSTAP_V25" and connect to this AP with the password "myzr2012".
Test Results
  1. Information generated when the device is successfully connected

=====> Output information:  
Sending OFFER of 192.168.12.20
Sending OFFER of 192.168.12.20
Sending ACK to 192.168.12.20

  2. Information generated when a device is disconnected

=====> Output information:  
RTL871X: OnDeAuth(wlan0) reason=3, ta=b4:0b:44:f5:64:2f
RTL871X: clear key for addr:b4:0b:44:f5:64:2f, camid:4


EC20 Module test

  【Test instruction】:After the 4G connection is successful, the development board sends an ICMP packet to the external network to verify that the connection is normal.
  【Interface identifier】:MINI_PCIE
  【System equipment】:eth2
Test operation
  1. The development board is powered off, connected to the 4G module, connected to the antenna and inserted into the SIM card to start the evaluation board.
  2. Use the instructions to make a network connection:

=====> Enter the command: 
/my-demo/gcc-linaro-5.3-arm/quectel-CM &

=====> Output information:  
[1] 540
[12-18_03:17:06:719] WCDMA&LTE_QConnectManager_Linux&Android_V1.1.34
[12-18_03:17:06:720] /my-demo/gcc-linaro-5.3-arm/quectel-CM profile[1] = (null)/(null)/(null)/0, pincode = (null)
[12-18_03:17:06:723] Find /sys/bus/usb/devices/1-1.2 idVendor=2c7c idProduct=0125
[12-18_03:17:06:723] Find /sys/bus/usb/devices/1-1.2:1.4/net/eth2
[12-18_03:17:06:723] Find usbnet_adapter = eth2
[12-18_03:17:06:723] Find /sys/bus/usb/devices/1-1.2:1.4/GobiQMI/qcqmi2
[12-18_03:17:06:724] Find qmichannel = /dev/qcqmi2
[12-18_03:17:06:794] Get clientWDS = 7
[12-18_03:17:06:826] Get clientDMS = 8
[12-18_03:17:06:858] Get clientNAS = 9
[12-18_03:17:06:890] Get clientUIM = 10
[12-18_03:17:06:922] Get clientWDA = 11
[12-18_03:17:06:954] requestBaseBandVersion EC20CEFAR02A10M4G
[12-18_03:17:07:050] requestGetSIMStatus SIMStatus: SIM_READY
[12-18_03:17:07:082] requestGetProfile[1] cmnet///0
[12-18_03:17:07:114] requestRegistrationState2 MCC: 460, MNC: 0, PS: Attached, DataCap: LTE
[12-18_03:17:07:146] requestQueryDataCall IPv4ConnectionStatus: DISCONNECTED
[12-18_03:17:07:223] requestRegistrationState2 MCC: 460, MNC: 0, PS: Attached, DataCap: LTE
[12-18_03:17:07:274] requestSetupDataCall WdsConnectionIPv4Handle: 0x8777e7a0
[12-18_03:17:07:370] requestQueryDataCall IPv4ConnectionStatus: CONNECTED
[12-18_03:17:07:403] ifconfig eth2 up
[12-18_03:17:07:452] busybox udhcpc -f -n -q -t 5 -i eth2
[12-18_03:17:07:492] udhcpc (v1.23.1) started
[12-18_03:17:07:656] Sending discover...
[12-18_03:17:07:706] Sending select for 10.25.154.46...
[12-18_03:17:07:766] Lease of 10.25.154.46 obtained, lease time 7200
[12-18_03:17:07:888] /etc/udhcpc.d/50default: Adding DNS 211.136.17.107
[12-18_03:17:07:888] /etc/udhcpc.d/50default: Adding DNS 211.136.20.203

  3. Test connection

=====> Enter the command:
ping -I eth2 www.baidu.com -c 2 -w 4

=====> Output information: 
PING www.baidu.com (14.215.177.38): 56 data bytes
64 bytes from 14.215.177.38: seq=0 ttl=49 time=15.753 ms
64 bytes from 14.215.177.38: seq=1 ttl=49 time=11.835 ms

--- www.baidu.com ping statistics ---
2 packets transmitted, 2 packets received, 0% packet loss
round-trip min/avg/max = 11.835/13.794/15.753 ms

Test Results
  “0% packet loss” Indicates that the WIFI connection is normal.


--------------------------------------------------------------------------------
* ZhuHai MYZR Technology CO.,LTD.
* Latest Update: 2019/02/19  
* Supporter: Tang Bin
--------------------------------------------------------------------------------