MYZR-SAMA5-CB200 硬件介绍

来自明远智睿的wiki
Admin讨论 | 贡献2018年1月29日 (一) 09:08的版本 MY-IMX6-CB200配置(MY-IMX6-CB200 configuration)

跳转至: 导航搜索

目录

= MY-SAMA5-CB200视图(MY-SAMA5-CB200 view) =

正面视图(top view)

MY-SAMA5-CB200 1.1.0.1.png

背面视图(bottom view)

MY-SAMA5-CB200 1.2.0.1.png

= SAMA5D3 MPU概览(SAMA5D3 MPU overview) =

SAMA5D3简介(SAMA5D3 MPU introduction)

  Atmel | SMART SAMA5D3 MPU 能在低于 150mW 的功耗下提供高达 850DMIPS 的处理能力,是所有高性能、低功耗、成本敏感型工业应用的理想之选。其应用包括控制面板、智能电网设备和条形码扫描仪,即,需要高级别的连接性、增强的用户界面、稳定可靠的安全性或电池供电的任何设备。SAMA5D3 还是低功耗、小尺寸都至关重要的穿戴式计算应用和移动应用的理想之选。SAMA5D3 系列包括支持 -40/+105°C 温度范围以及 12x12mm BGA324 封装(间距为 0.5mm)的器件。
SMART SAMA5D3 MPU can provide processing capacity of up to 850DMIPS with power consumption of less than 150mW,which is the best choice for industrial application featuring high performance,low power consumption and senstiveness to cost.its application includes controling of panel,smart power facility and barcode scanner,e.g.any device which need high grade connection,enhanced user interface,high safety or to be powered by battery.SAMA5D3 is also the good choice for wearable computing application and mobile application.SAMA5D3 series include components of which support temperature range -40/+105°C and package of 12x12mm BGA324(space as 0.5mm)
  Atmel | SMART? SAMA5D3 系列以 536 Mhz 提供高达 850DMIPS 的处理能力,功耗水平市场领先(在工作模式下低于 150 mW;在低功耗模式下低于 0.5 mW)。通过支持高精度计算和快速数据处理的 FPU,以及 64 位内部总线架构和 32 位宽 DDR 控制器(能够以高达 166 MHz 的频率运行,提供高达 1328 MB/s 的带宽),实现了高性能。功能强大的外设包括多达三个的高速 USB 端口、千兆位和 10/100 以太网、双 CAN、TFT LCD 控制器、相机接口、三个 SDIO/SD/MMC、UART、SPI、TWI、软调制解调器、12 位 ADC、32 位定时器等。稳定可靠的安全性和防假冒由硬件加密引擎(如 AES/3DES、TRNG、SHA)和安全引导提供。这些器件随附免费 Atmel Linux? 分发包、Android 分发包、Qt SDK 以及一套完整的面向非操作系统用户的 C 示例。来自多个软件和硬件合作伙伴的 SOM(模块系统)、PMIC(电源管理IC)、内存和套件令本产品更加完整。
SMART SAMA5D3 series can provide processing capacity of up to 50DMIPS at 536 Mhz,it is advanced in the market in terms of power consumption(less than 150mW in working mode,less than 0.2-5mW in low-power mode).it provides powerful and high performance external components and interfaces,including 3 USB ports in high speed,interfaces for GMbps and 10/100 ethernet,dual CAN and TFT LCD controller,camera,3 soft modulators of SDIO/SD/MMC、UART、SPI、TWI,12 bit ADC,32 bit timer and ect.Highly stable and reliable safety and Counterfeit prevention is offered by hardware encrypt engine( such as AES/3DES、TRNG、SHA) and safety leading.free Atmel Linux? distribution,Android distribution package,Qt SDK and a full set of C example for non-operating system users are attached with these components.SOM(module system),PMIC(power management IC),memory and kits from different software and hardware partners will make this item more completed.

SAMA5D3优势(SAMA5D3 advantage)

  • ARM Cortex-A5 内核以 536MHz (850DMIPS) 运行。

ARM Cortex-A5 kernel runs at 536MHz (850DMIPS)

  • 用于高精度计算和快速数据处理的浮点运算单元 (FPU)。

floating point arithmetic unit is used for high precise calculation and fast data process

  • 市场领先的低功耗优势

superior low-consumption is leading in the market

    • 在激活所有外设的情况下,以低于 150mW 的功耗(在工作模式下)提供高达 536MHz 的工作频率。

with all external devices activated,it can provide up to 536MHz working frequency with less than 150mW(in working mode)

    • 在具有 SRAM 和寄存器保留的情况下,低功耗模式下的功耗低于 0.5mW。

with SRAM and register,power consumption is as low as 0.5mW in low-consumption mode

    • 双 CAN 控制器。

dual CAN control

  • 支持 IEEE1588 的千兆位以太网 MAC 和 10/100 MAC。

support IEEE1588 Gmbps ethernet MAC and 10/100 MAC

  • 三个 HS 高速 USB 端口(可配置为三个主机或两个主机和一个器件端口)。

3 HS high speed USB ports(can be configured to 3 hosts or two host+one component port)

  • CMOS 图像传感器接口。

CMOS image sensor interface

  • 图形 LCD 控制器,具有图像合成叠加

graphic LCD controller,features Image synthesis and superimposition

  • AES/3DES 硬件加密引擎和安全引导。

AES/3DES hardware encrypt engine and safty leading

  • BGA324(15x15,间距为 0.8)封装,以及小封装选项 BGA(12x12mm,间距为 0.5)。

BGA324(15x15,invterval 0.8)package,and small package option BGA(12x12mm,interval 0.5)

  • 扩展的工业温度范围:-40°C 到 105°C。

expanded industrial temperature range:-40°C to 105°C

SAMA5D3简图(SAMA5D3 diagram)

MY-SAMA5-CB200 2.3.0.1.png

SAMA5D3框图 (SAMA5D3 block diagram)

MY-SAMA5-CB200 2.4.0.1.png

SAMA5D3 MPU差异(SAMA5D3 MPU difference)

MY-SAMA5-CB200 2.5.0.1.png

SAMA5D36关键参数(SAMA5D36 critical parameter)

Parameter
<thead> </thead> <tbody> </tbody>
Value
Pin Count:
324
-
Max. Operating Freq. (MHz):
536 MHz
-
CPU:
Cortex-A5
-
Max I/O Pins:
160
-
Ext Interrupts:
160
-
USB Transceiver:
3
-
USB Speed:
Hi-Speed
-
USB Interface:
Host, Device
-
SPI:
6
-
TWI (I2C):
3
-
UART:
7
-
CAN:
2
-
LIN:
4
-
SSC:
2
-
Ethernet:
2
-
SD / eMMC:
3
-
Graphic LCD:
Yes
-
Camera Interface:
Yes
-
ADC Channels:
12
-
ADC Resolution (bits):
12
-
ADC Speed (ksps):
1000
-
Resistive Touch Screen:
Yes
-
Crypto Engine:
AES/DES/SHA/TRNG
-
SRAM (Kbytes):
128
-
External Bus Interface:
1
-
DRAM Memory:
DDR2/LPDDR/LPDDR2
-
NAND Interface:
Yes
-
Temp. Range (deg C):
-40 to 105
-
I/O Supply Class:
1.8/3.3
-
Operating Voltage (Vcc):
1.08 to 1.32
-
FPU:
Yes
-
Timers:
6
-
Output Compare Channels:
6
-
Input Capture Channels:
6
-
PWM Channels:
4
-
32kHz RTC:
Yes
-
MPU / MMU:
No / Yes
-
Quadrature Decoder Channels:
0
-
Video Decoder:
No
}

SAMA5D3-CB200配置(SAMA5D3-CB200 configuration)

== 硬件配置(hardware configuration) ==

CPU
SAMA5D3x
<thead> </thead> <tbody> </tbody>
工业级/扩展工业级
(industrial/expansion)
内存
(memory)
256MB
可扩展到512MB
(can be expanded to 512MB)
-
存储
(storage)
256MB
最大可支持到2GB
(support up to 2GB)
-
SPI Flash
2M
支持烧录
(support programming)
-
启动模式
(boot mode)
SPI启动
(SPI boot)
确保产品的稳定可靠
(ensure the stability and reliability of products)
}

工作温度范围(working temperature range)

  • 工业级

industrial grade

           -40°C ~ 85°C
  • 扩展工业级

expanded industial grade

           -40°C ~ 105°C

操作系统支持(operation system support)

  • 内核:Linux-3.18

kernel: Linux-3.18

  • 界面:命令行,QT5

interface:command line,

型号命令(model command)

型号名称组成(name of model)

MY-SAMA5-CB200-MPU规格-内存容量-存储容量
MY-SAMA5-CB200-MPU specification-memory capacity-storage capacity

MPU规格(MPU specification)

D36ACN, D36ACNR: 工业扩展级
D36ACN, D36ACNR:industrial expansion
D36ACU, D36ACUR: 工业级
D36ACU, D36ACUR: industrial

内存容量(memory capacity)

256MB: 256兆内存
256MB:256G memory

存储容量(storage capacity)

256MB: 256兆存储
256MB:256G storge

型号举例(example of model)

MY-SAMA5-CB200-D36ACN-256M-256M

MY-SAMA5-CB200定义(MY-SAMA5-CB200 definition)

序号
Num
引脚
Pin
默认信号
Default signal
默认接口
Default Interface
可复用的信号
Multiplex
  可复用的信号
Multiplex
默认接口
Default Interface
默认信号
Default signal
引脚
Pin
序号
Num.
<thead> </thead> <tbody> </tbody>
1 GND_POWER               GND_POWER 2
3 PC1 ETX1 rowspan=10 EMAC TIOB3   LCDDAT19
rowspan=6 MCI2
MCI2_DA0
PC11
4
-
5 PC8 EMDC
TCLK5
 
LCDDAT18|TIOA1 MCI2_DA1
PC12
<thead> </thead> <tbody> </tbody>
6
7
PC3
ERX1
TIOA4
 
LCDDAT21|PCK2 MCI2_CK
PC15
<thead> </thead> <tbody> </tbody>
8
9
PC6
ERXER
TIOA5
 
LCDDAT17|TIOB1 MCI2_DA2
PC13
<thead> </thead> <tbody> </tbody>
10
11
PC4
ETXEN
TIOB4
 
LCDDAT20 MCI2_CDA
PC10
<thead> </thead> <tbody> </tbody>
12
13
PC7
EREFCK
TIOB5
 
LCDDAT16|TCLK1 MCI2_DA3
PC14
<thead> </thead> <tbody> </tbody>
14
15
PC0
ETX0
TIOA3
 
 
SSC0 RK0
PC19
<thead> </thead> <tbody> </tbody>
16
17 ||PC2 ||ERX0 ||TCLK3 ||  || ||TF0 ||PC17 ||18
-
19
PC5
ECRSDV
TCLK4
   

RF0
PC20
<thead> </thead> <tbody> </tbody>
20
21
PC9
EMDIO
 
 
  RD0
PC21
<thead> </thead> <tbody> </tbody>
22
23
PC30
UTXD0
rowspan=2|UART0
ISI_PCK
 
 
TK0
PC16
<thead> </thead> <tbody> </tbody>
24
25
PC29
URXD0
ISI_D8|PWMFI2
 
  TD0
PC18
<thead> </thead> <tbody> </tbody>
26
27
GND_POWER
 
 
 
 
 
 
 
GND_POWER
28
-
29
PC31
 
 
PWMFI1|FIQ
 
 
rowspan=2|LCDC
LCDVSYNC
PA26
30
-
31 ||PC23 ||SPI1_MOSI ||rowspan=5|SPI1 ||    ||  || ||LCDDISP ||PA25 ||32
-
33 ||PC25 ||SPI1_NPCS0 ||  ||  ||  ||  ||  ||GND_POWER ||34
-
35 ||PC22 ||SPI1_MISO ||  ||  ||  ||LCDC ||LCDHSYNC ||PA27 ||36
-
37 ||PC24 ||SPI1_SPCK ||  ||  ||  ||  ||  ||GND_POWER ||38
-
39 ||PC28 ||SPI1_NPCS3 ||ISI_D9|PWMFI0 ||  ||  ||rowspan=15|LCDC ||LCDDEN ||PA29 ||40
-
41 ||PA4 ||LCDDAT4 ||rowspan=12|LCDC ||  ||  ||  ||LCDDAT2 ||PA2 ||42
-
43 ||PA10 ||LCDDAT10 ||  ||  ||  ||LCDDAT15 ||PA15 ||44
-
45 ||PA14 ||LCDDAT14 ||  ||  ||ISI_D1 ||LCDDAT17 ||PA17 ||46
-
47 ||PA12 ||LCDDAT12 ||  ||  ||  ||LCDDAT1 ||PA1 ||48
-
49 ||PA24 ||LCDPWM ||  ||  ||  ||LCDDAT0 ||PA0 ||50
-
51 ||PA22 ||LCDDAT22 ||ISI_D6|PWMH1 ||  ||  ||LCDDAT3 ||PA3 ||52
-
53 ||PA28 ||LCDPCK ||  ||  ||  ||LCDDAT8 ||PA8 ||54
-
55 ||PA20 ||LCDDAT20 ||ISI_D4|PWMH0 ||  ||  ||LCDDAT6 ||PA6 ||56
-
57 ||PA21 ||LCDDAT21 ||ISI_D5|PWML0 ||  ||ISI_D2|TWD2 ||LCDDAT18 ||PA18 ||58
-
59 ||PA23 ||LCDDAT23 ||ISI_D7|PWML1 ||  ||ISI_D0 ||LCDDAT16 ||PA16 ||60
-
61 ||PA5 ||LCDDAT5 ||  ||  ||ISI_D3|TWCK2 ||LCDDAT19 ||PA19 ||62
-
63 ||PA7 ||LCDDAT7 ||  ||  ||  ||LCDDAT11 ||PA11 ||64
-
65 ||PA30 ||TWD0 ||rowspan=2|TWI0 ||URXD1|ISI_VSYNC ||  ||  ||LCDDAT9 ||PA9 ||66
-
67 ||PA31 ||TWCK0 ||UTXD1|ISI_HSYNC ||  ||  ||LCDDAT13 ||PA13 ||68
-
69 ||PD31 ||  ||  ||PCK1|AD11 ||  ||ISI_D10|SPI1_NPCS2 ||rowspan=2|TWI1 ||TWCK1 ||PC27 ||70
-
71 ||PD30 ||PCK0 ||SSC0:CLK ||AD10 ||  ||ISI_D11|SPI1_NPCS1 ||TWD1 ||PC26 ||72
-
73 ||PD29 ||AD9 ||rowspan=10|AD ||  ||  ||  ||rowspan=8|MCI0 ||MCI0_DA3 ||PD4 ||74
-
75 ||PD28 ||AD8 ||   ||  ||  ||MCI0_DA1 ||PD2 ||76
-
77 ||PD27 ||AD7 ||   ||  ||  ||MCI0_CDA ||PD0 ||78
-
79 ||PD26 ||AD6 ||   ||  ||  ||MCI0_CK ||PD9 ||80
-
81 ||PD23 ||AD3 ||   ||  ||  ||MCI0_DA2 ||PD3 ||82
-
83 ||PD22 ||AD2 ||   ||  ||  ||MCI0_DA0 ||PD1 ||84
-
85 ||PD24 ||AD4 ||   ||  ||PWML2|TIOB0 ||MCI0_DA5 ||PD6 ||86
-
87 ||PD21 ||AD1 ||   ||  ||PWML3 ||MCI0_DA7 ||PD8 ||88
-
89 ||PD25 ||AD5 ||   ||  ||SPI0_NPCS2|CTS0 ||rowspan=2|CAN0 ||CANTX0 ||PD15 ||90
-
91 ||PD20 ||AD0 ||   ||  ||SPI0_NPCS1|SCK0 ||CANRX0 ||PD14 ||92
-
93 ||PD5 ||PWMH2 ||rowspan=2|PWM ||MCI0_DA4|TIOA0 ||  ||  ||UART0 ||TXD0 ||PD18 ||94
-
95 ||PD7 ||PWMH3 ||MCI0_DA6|TCLK0 ||  ||  || ||RXD0 ||PD17 ||96
-
97 ||PD19 ||  ||GPIO ||ADTRG ||  ||  ||rowspan=3|SPI0 ||SPI0_MISO ||PD10 ||98
-
99 ||PB0 ||GTX0 ||rowspan=15|GMAC ||PWMH0 ||    || ||SPI0_SPCK ||PD12 ||100
-
101 ||PB7 ||GRX3 ||RK1 ||  ||  ||SPI0_MOSI ||PD11 ||102
-
103 ||PB13 ||GRXER ||PWML3 ||  ||PWMH3|GRXDV ||GMAC:INTRP ||  ||PB12 ||104
-
105 ||PB17 ||GMDIO ||  ||  ||GCOL ||rowspan=2|CAN0 ||CANTX1 ||PB15 ||106
-
107 ||PB11 ||GRXCK ||RD1 ||  ||GCRS ||CANRX1 ||PB14 ||108
-
109 ||PB18 ||G125CK ||  ||  ||GTX7 ||rowspan=6|MCI1 ||MCI1_DA2 ||PB22 ||110
-
111 ||PB1 ||GTX1 ||PWML0 ||  ||GRX5 ||MCI1_CK ||PB24 ||112
-
113 ||PB4 ||GRX0 ||PWMH1 ||  ||GTX5 ||MCI1_DA0 ||PB20 ||114
-
115 ||PB3 ||GTX3 ||TF1 ||  ||GTX6 ||MCI1_DA1 ||PB21 ||116
-
117 ||PB8 ||GTXCK ||PWMH2 ||  ||GTX4 ||MCI1_CDA ||PB19 ||118
-
119 ||PB9 ||GTXEN ||PWML2 ||  ||GRX4 ||MCI1_DA3 ||PB23 ||120
-
121 ||PB2 ||GTX2 ||TK1 ||  ||G125CKO ||rowspan=4|USART1 ||RTS1 ||PB27 ||122
-
123 ||PB6 ||GRX2 ||TD1 ||  ||  ||RXD1 ||PB28 ||124
-
125 ||PB5 ||GRX1 ||PWML1 ||  ||  ||TXD1 ||PB29 ||126
-
127 ||PB16 ||GMDC ||  ||  ||GRX7 ||CTS1 ||PB26 ||128
-
129 ||PB25 ||  ||  ||SCK1|GRX6 ||  ||RF1|GTXER ||EMAC:INT_N ||  ||PB10 ||130
-
131 ||BMS ||  ||  ||  ||  ||  ||  ||  ||DIBN ||132
-
133 ||NRST ||  ||  ||  ||  ||  ||  ||  ||DIBP ||134
-
135 ||TDI ||  ||  ||  ||  ||  ||rowspan=2|DEBUG ||DTXD ||PB31 ||136
-
137 ||JTAGSEL ||  ||  ||  ||  ||  ||DRXD ||PB30 ||138
-
139 ||TCK ||SWCLK ||  ||  ||  ||PWMFI3|SPI0_NPCS3|RTS0 ||SSC0:IRQ ||  ||PD16 ||140
-
141 ||TMS ||SWDIO ||  ||  ||  ||  ||  ||  ||GND_POWER ||142
-
143 ||TDO ||  ||  ||  ||  ||  ||USBA ||DHSDP ||HHSDPA ||144
-
145 ||NTRST ||  ||  ||  ||  ||  || ||DHSDM ||HHSDMA ||146
-
147 ||WKUP ||  ||  ||  ||  ||  ||USBB ||  ||HHSDPB ||148
-
149 ||SHDN ||  ||  ||  ||  ||  || ||  ||HHSDMB ||150
-
151 ||D7 ||  ||rowspan=8|EBI:Dx ||  ||  ||  ||USBC ||  ||HHSDMC ||152
-
153 ||D6 ||  ||  ||  ||  || ||  ||HHSDPC ||154
-
155 ||D5 ||  ||  ||  ||LCDDAT23|TIOB2 ||rowspan=10|EBI ||NCS2 ||PE28 ||156
-
157 ||D4 ||  ||  ||  ||LCDDAT22|TIOA2 ||NCS1 ||PE27 ||158
-
159 ||D3 ||  ||  ||  ||USART2:CTS2 ||A23 ||PE23 ||160
-
161 ||D2 ||  ||  ||  ||USART2:RXD2 ||A25 ||PE25 ||162
-
163 ||D1 ||  ||  ||  ||USART2:TXD2 ||NCS0 ||PE26 ||164
-
165 ||D0 ||  ||  ||  ||  ||A20 ||PE20 ||166
-
167 ||PE3 ||A3 ||rowspan=11|EBI:Ax ||GPIO:LED ||  ||USART2:RTS2 ||A24 ||PE24 ||168
-
169 ||PE5 ||A5 ||   ||  ||TCLK2 ||NWR1/NBS1 ||PE29 ||170
-
171 ||PE6 ||A6 ||   ||  ||USART3:RXD3 ||A18 ||PE18 ||172
-
173 ||PE13 ||A13 ||   ||  ||USART3:TXD3 ||A19 ||PE19 ||174
-
175 ||PE15 ||A15 ||SCK3 ||  ||PWML1|IRQ ||MMC1:VDD_EN ||  ||PE31 ||176
-
177 ||PE8 ||A8 ||  ||  ||NWAIT ||MMC1:CD ||  ||PE30 ||178
-
179 ||PE10 ||A10 ||  ||  ||GPIO:LED ||rowspan=7|EBI:Ax ||A4 ||PE4 ||180
-
181 ||PE14 ||A14 ||  ||  ||GPIO:LED ||A2 ||PE2 ||182
-
183 ||PE16 ||A16 ||CTS3 ||  ||GPIO:LED ||A1 ||PE1 ||184
-
185 ||PE0 ||A0/NBS0 ||  ||  ||  ||A7 ||PE7 ||186
-
187 ||PE11 ||A11 ||  ||  ||RTS3 ||A17 ||PE17 ||188
-
189 ||GND_POWER ||  ||  ||  ||  ||  ||A9 ||PE9 ||190
-
191 ||GND_POWER ||  ||  ||  ||  ||  ||A12 ||PE12 ||192
-
193 ||GND_POWER ||  ||  ||  ||  ||  ||  ||  ||VCC_3V3 ||194
-
195 ||GND_POWER ||  ||  ||  ||  ||  ||  ||  ||VCC_3V3 ||196
-
197 ||GND_POWER ||  ||  ||  ||  ||  ||  ||  ||VCC_3V3 ||198
-
199 ||GND_POWER ||  ||  ||  ||  ||  ||  ||  ||VCC_3V3 ||200
-
colspan=11|说明1:“可复用的信号”栏中黄色背景表示在MY-SAMA5-EK200上实现的信号。
instruction1: in the column of "multiplex signal" signal highlighted in yellow are the ones realized by MY-SAMA5-EK200
说明2:MY-SAMA5-CB200-D36引出的管脚主要有PA0~PA31、PB0~PB31、PC0~PC31、PD0~PD12、PD14~PD31、PE0~PE20、PE23~PE31。
instruction2:pins led out by MY-SAMA5-CB200-D36 are PA0~PA31、PB0~PB31、PC0~PC31、PD0~PD12、PD14~PD31、PE0~PE20、PE23~PE31

= SAMA5D3 MPU介绍(SAMA5D3 MPU introduction) =

SAMA5关键亮点(SAMA5 main features)

高性能(high performance)

  SAMA5 系列是专为弥补 ARM Cortex-A5 内核在功率方面的不足而设计,包括的器件能以低至 150 mW 的功耗提供高达 945DMIPS 的处理能力。
SAMA5 series is designed an an improvement for ARM Cortex-A5 in terms of insufficient power,its components can provide processing capacity up to 945DMIPS at power consumption less than 150mW

1.58 DMIPS/MHz ARM Cortex-A5 内核

</em>1.58 DMIPS/MHz ARM Cortex-A5 kernel

高达 600 MHz 的最大工作频率 (945DMIPS)

the maximum working frequency(945DMIPS) is upt to 600 MHz

64 位内部总线架构、可提供高达 1600 MB/s 带宽的 32 位宽 DDR 控制器

64bit internal bus architecture,32bit DDR controller which can offer band width of up to 1600 MB/s

用于高精度计算和快速数据处理的 Neon 和浮点运算单元 (FPU)

Neon and floating point calculation unit is used for highly precise calculation and fast data process

ARM Cortex-A5 FPU 的性能是 ARM Cortex-A8 FPU 的三倍

capability of ARM Cortex-A5 FPU is 3 times higher than that of ARM Cortex-A8 FPU

  • L2 缓存,用于提高整体系统性能

L2 cache,is used to improve performance of the whole system

低功耗(low power consumption)

  SAMA5 器件采用创新技术以降低所有模式下的功耗,并且可实现:
SAMA5 components can lower effectively power consumption in all modes by applying innovative technology and fulfill following objectives:

在激活所有外设的情况下,以低于 150mW 的功耗(在工作模式下)提供高达 536MHz 的工作频率

with all external devices activated,it can provide up to 536MHz working frequency with less than 150mW(in working mode)

在运行 SRAM 和 寄存器保留的低功耗模式下,功耗低于 0.5mW 且唤醒时间短于 0.5ms。在运行RTC(实时时钟)的备份模式下功耗约为 1.2μA

in low power consumption mode with SRAM and register kept,the power consumption is as low as 0.5mW and waking up takes only less than 0.5ms.in backup mode of RTC(real time clock),the power consumption is about 1.2μA

  • 电池供电系统的理想之选

the best choice for the systems powered by battery

连接性(connectivity)

  SAMA5 器件嵌入了各种高级通信外设,因此是网桥和网关的理想之选。
SAMA5 components embed various kinds of high class communication external devices,so it is the best choice for network bridge and gateway

支持 IEEE1588 的以太网 MAC 和千兆位以太网 MAC、双 CAN 端口

support IEEE1588 ethernet MAC and Gbps ethernet MAC,dual CAN ports

可配置为三个主机或两个主机及一个器件端口的三个高速 USB 端口

can be configured to 3 hosts or two host+3 high speed USB interfaces of one component port

  • 多个 SDIO/SD/MMC 端口、UART、SPI、TWI、软调制解调器、CMOS 图像传感器接口、ADC、32 位定时器等。有关更多详细信息,请参阅“器件概述”选项卡

multiple SDIO/SD/MMC interface、UART、SPI、TWI、soft modulator、CMOS image sensor interface、ADC、32 timer and ect. please refer to "component overview" tab for more details.

增强的用户界面(enhanced user interface)

  使用 SAMA5 MPU,可以创建当今应用所需的时尚、平稳的用户界面。
you can create upt to date user interface in fashionable,stable style with SAMA5 MPU.

图形 LCD 控制器具有图像合成叠加和集成功能(如 α 混合、缩放、颜色转换和旋转)

graphic LCD controller features synthesis and superimposition of image and integration( such as αblend,zoom,color transform and rotation)

720p 硬件视频解码器,用于加快支持当今主流视频标准的视频回放

720p hardware video decoder is used to support playback of vedio in current main stream standard

电阻式触摸屏界面

resistance touch screen interface

CMOS 图像传感器接口

CMOS image sensor interface

安全(safe)

  SAMA5 系列包括防止克隆、确保真实性以及保护应用的通信和数据存储安全的功能。
safety of SAMA5 series incudes functions of preventing copy,ensuring facticity and protecting application communication and data storage

安全引导

satefy boot

硬件加密引擎,如高级加密标准 (AES)/三重数据加密标准 (DES)、RSA (Rivest-Shamir-Adleman) 和 ECC(椭圆曲线加密)以及安全哈希算法 (SHA) 和真正的随机号码生成器 (TRNG)

hardware encrypt engine,such as high class encrypt standard(AES)/triple data encription standard (DES)、RSA (Rivest-Shamir-Adleman) and ECC(elliptic curve crypto) and secure hash algorithm(SHA) and true Random number generator(TRNG)

通过外部 DDR 内存即时加密/解密代码

immediately encrypt code/decode through external DDR memory

管脚篡改检测,以保护系统免受物理入侵

detect tamper of pin, to protect system from physical intruding

密钥和数据的安全存储

cipher key and data safe storage

ARM 信任区域,用于对系统、外设和内存资源进行分区,以将安全关键型软件与开放环境操作系统隔离

ARM trusted area is for the partition among system,peripherals and internal resources to isolate the main software related to safety with environment operating system

安全性(safety)

  SAMA5 系列具有的功能可轻松简便地实施如 IEC61508 等安全标准。
functions possessed by SAMA5 can meet easiy with the safety standard such as IEC61508

主晶体振荡器时钟具有故障检测器

main crystal oscillator cock can work as a fault detector

上电复位

power on and reset

独立的看门狗定时器

independent watch dog timer

寄存器写保护

writing protection of register

内存管理单元 (MMU) 允许在内存内设置区域保护

memory management unit allow a setting of zone prorection in the memory

基于 SHA 的 ICM(完整性检查监控器),用于验证内存内容的完整性

ICM(monitor of integrity) based on SHA is used to verify integrity of content in memory

  • Arm 信任区域

Arm tursted zone

低系统成本(low cost of system)

  SAMA5 凭借高度的系统集成,在实现最大灵活性的同时还减少了对其他昂贵组件的需求。
SAMA5 realize the purpose of maximum flexibility and the the same time reducing demands for other expensive components by high integrity of system

0.8mm 球间距封装简化了 PCB 设计并降低了成本

0.8mm ball spacing package simplify PCB design and lower cost

最低功耗方案,需要芯片离散的电源或低成本 PMIC

scheme for minimum low consumption need Chip discrete power and low cost

三个高速 USB 端口节省了外部集线器的成本

3 high speed USB ports help to save the cost for external integrator

DDR(双数据速率)内存线路上的阻抗控件节省了外部电阻器

impedance control on memory circuit of DDR(dual data rate) save exteranl resistors

嵌入式 RTC 节省了外部组件

embeded RTC save external components

集成的软调制解调器解决方案节省了外部调制解调器设备的成本

solution with soft modulator integrated save cost for adding external modulator

SAMA5D3 Features

Core

  • ARM Cortex-A5 Processor with ARM v7-A Thumb2? Instruction Set
    • CPU Frequency up to 536 MHz
  • 32 Kbyte Data Cache, 32 Kbyte Instruction Cache, Virtual Memory System Architecture (VMSA)
  • Fully Integrated MMU and Floating Point Unit (VFPv4)

Memories

One 160 Kbyte Internal ROM Single-cycle Access at System Speed, Embedded Boot Loader: Boot on 8-bit
NAND Flash, SDCard, eMMC, serial DataFlash?, selectable Order
One 128 Kbyte Internal SRAM, Single-cycle Access at System Speed
High Bandwidth 32-bit Multi-port Dynamic RAM Controller supporting 512 Mbyte 8 bank DDR2/LPDDR/LPDDR2 with datapath scrambling
Independent Static Memory Controller with datapath scrambling and SLC/MLC NAND Support with up to 24-bit Error Correcting Code (PMECC)

System running up to 166 MHz

Reset Controller, Shut Down Controller, Periodic Interval Timer, Watchdog Timer and Real-time Clock
Boot Mode Select Option, Remap Command
Internal Low-power 32 kHz RC Oscillator and Fast 12 MHz RC Oscillator
Selectable 32768 Hz Low-power Oscillator and 12 MHz Oscillator
One 400 to 1000 MHz PLL for the System and one PLL at 480 MHz optimize d for USB High Speed
39 DMA Channels including two 8-channel 64-bit Central DMA Controllers
64-bit Advanced Interrupt Controller
Three Programmable External Clock Signals
Programmable Fuse Box with 256 fuse bits, 192 of them available for Customer

Low Power Management

Shut Down Controller
Battery Backup Registers
Clock Generator and Power Management Controller
Very Slow Clock Operating Mode, Software Programmable Power Optimization Capabilities

Peripherals

LCD TFT Controller with Overlay, Alpha-blending,Rotation, Scaling and Color Space Conversion
ITU-R BT. 601/656 Image Sensor Interface
Three HS/FS/LS USB Ports with On-Chip Transceivers
One Device Controller
One Host Controller with Integrated Root Hub (3 Downstream Ports)
One 10/100/1000 Mbps Gigabit Ethernet MAC Controller (GMAC) with IEEE1588 support
One 10/100 Mbps Ethernet MAC Controller (EMAC)
Two CAN Controllers with 8 Mailboxes, fully Compliant with CAN 2.0 Part A and 2.0 Part B
Softmodem Interface
Three High Speed Memory Card Hosts (eMMC 4.3 and SD 2.0)
Two Master/Slave Serial Peripheral Interfaces
Two Synchronous Serial Controllers
Three Two-wire Interface up to 400 Kbit/s supporting I2C Protocol and SMBUS
Four USARTs, two UARTs, one DBGU
Two Three-channel 32-bit Timer/Counters
One 4-channel 16-bit PWM Controller
  • One 12-channel 12-bit Analog-to-Digital Converter with Resistive Touch-Screen function

Safety

Power-on Reset Cells
Independent Watchdog
Main Crystal Clock Failure Detection
Write Protection Registers
SHA: Supports Secure Hash Algorithm (SHA1, SHA224, SHA 256, SHA384, SHA512)
Memory Management Unit

Security

TRNG: True Random Number Generator
Encryption Engine
AES: 256-bit, 192-bit, 128-bit Key Algorithm, Compliant with FIPS PUB 197 Specifications
TDES: Two-key or Three-key Algorithms, Co mpliant with FIPS PUB 46-3 Specifications
  • Atmel? Secure Boot Solution

I/O

Five 32-bit Parallel Input/Output Controllers
160 I/Os
Input Change Interrupt Capability on Each I/O Line, Selectable Schmitt Trigger Input
Individually Programmable Open-drain, Pull-up and Pull-down Resistor, Synchronous Output, Filtering
Slew Rate Control on High Speed I/Os
Impedance Control on DDR I/Os

Package

324-ball LFBGA, 15 x 15 x 1.4 mm, pitch 0.8 mm
324-ball TFBGA, 12 x 12 x 1.2 mm, pitch 0.5 mm

SAMA5D3 Embedded Characteristics

WDT

12-bit key-protected programmable counter
Watchdog Clock is independent from Processor Clock
Provides reset or interrupt signals to the system
Counter may be stopped while the processor is in debug state or in idle mode

RTC

Ultra Low Power Consumption
Full Asynchronous Design
Gregorian Calendar up to 2099
Programmable Periodic Interrupt
  • Safety/security features:
    • Valid Time and Date Programmation Check

PIO

Up to 32 Programmable I/O Lines
Fully Programmable through Set/Clear Registers
Multiplexing of Four Peripheral Functions per I/O Line
For each I/O Line (Whether Assigned to a Peripheral or Used as General Purpose I/O)
Input Change Interrupt
Programmable Glitch Filter
Programmable Debouncing Filter
Multi-drive Option Enables Driving in Open Drain
Programmable Pull-Up on Each I/O Line
Pin Data Status Register, Supplies Visibility of the Level on the Pin at Any Time
Additional Interrupt Modes on a Programmable Event: Rising Edge, Falling Edge, Low-Level or High-Level
Lock of the Configuration by the Connected Peripheral
Synchronous Output, Provides Set and Clear of Several I/O Lines in a Single Write
Register Write Protection
Programmable Schmitt Trigger Inputs
Programmable I/O Drive

LCDC

Dual AHB Master Interface
Supports Single Scan Active TFT Display
Supports 12-, 16-, 18- and 24-bit Output Mode through the Spatial Dithering Unit
Asynchronous Output Mode Supported (at synthesis time)
1, 2, 4, 8 bits per pixel (palletized)
12, 16, 18, 19, 24, 25 and 32 bits per pixel (non palletized)
Supports One Base Layer (background)
Supports Two Overlay Layer Windows
Supports One High End Overlay (HEO) Window
Supports One Hardware Cursor, Fixed or Free Size
Hardware Cursor Fixed Size on the following patterns: 32x32, 64x64 and 128x128
Little Endian Memory Organization
Programmable Timing Engine, with Integer Clock Divider
Programmable Polarity for Data, Line Synchro and Frame Synchro.
Display Size up to 2048x2048, or up to 720p in video format
Color Lookup Table with up to 256 entries and Predefined 8-bit Alpha
Programmable Negative and Positive Row Striding for all Layers
Programmable Negative and Positive Pixel Striding for all Overlay1, Overlay2 and HEO layers
High End Overlay supports 4:2:0 Planar Mode and Semiplanar Mode
High End Overlay supports 4:2:2 Planar Mode, Semiplanar Mode and Packed
High End Overlay includes Chroma Upsampling Unit
Horizontal and Vertical Rescaling unit with Edge Interpolation and Independent Non Integer Ratio
Hidden Layer Removal supported.
Integrates Fully Programmable Color Space Conversion
Overlay1, Overlay2 and High End Overlay Integrate Rotation Engine: 90, 180, 270
Blender Function Supports Arbitrary 8-bit Alpha Value and Chroma Keying
DMA User interface uses Linked List Structure and Add-to-queue Structure

ISI

ITU-R BT. 601/656 8-bit Mode External Interface Support
Supports up to 12-bit Grayscale CMOS Sensors
Support for ITU-R BT.656-4 SAV and EAV Synchronization
Vertical and Horizontal Resolutions up to 20482048
Preview Path
Up to 2048*2048 in Grayscale Mode
Up to 640480 in RGB Mode
32 Bytes FIFO on Codec Path
32 Bytes FIFO on Preview Path
Support for Packed Data Formatting for YCbCr 4:2:2 Formats
Preview Scaler to Generate Smaller Size image
Programmable Frame Capture Rate
VGA, QVGA, CIF, QCIF Formats Supported for LCD Preview
  • Custom Formats with Horizontal and Vertical Preview Size as Multiples of 16 Also Supported for LCD Preview

UDPHS

1 Device High Speed
1 UTMI transceiver shared between Host and Device
USB v2.0 High Speed Compliant, 480 Mbit/s
16 Endpoints up to 1024 bytes
Embedded Dual-port RAM for Endpoints
Suspend/Resume Logic (Command of UTMI)
Up to Three Memory Banks for Endpoints (Not for Control Endpoint)
8 KBytes of DPRAM

UHPHS

Compliant with Enhanced HCI Rev 1.0 Specification
Compliant with USB V2.0 High-speed
Supports High-speed 480 Mbps
Compliant with OpenHCI Rev 1.0 Specification
Compliant with USB V2.0 Full-speed and Low-speed Specification
Supports both Low-speed 1.5 Mbps and Full-speed 12 Mbps USB devices
Root Hub Integrated with 3 Downstream USB HS Ports
Embedded USB Transceivers
Supports Power Management
Hosts (A and B) High Speed (EHCI), Port A shared with UDPHS

GMAC

Compatible with IEEE Standard 802.3
10, 100 and 1000 Mbps operation
Full and half duplex operation at all supported speeds of operation
Statistics Counter Registers for RMON/MIB
MII/GMII/RGMII interface to the physical layer
Integrated physical coding
Direct memory access (DMA) interface to external memory
Programmable burst length and endianism for DMA
Interrupt generation to signal receive and transmit completion, or errors
Automatic pad and cyclic redundancy check (CRC) generation on transmitted frames
Frame extension and frame bursting at 1000 Mbps in half duplex mode
Automatic discard of frames received with errors
Receive and transmit IP, TCP and UDP checksum offload. Both IPv4 and IPv6 packet types supported
Address checking logic for four specific 48-bit addresses, four type IDs, promiscuous mode, hash matching of
unicast and multicast destination addresses and Wake-on-LAN
Management Data Input/Output (MDIO) interface for physical layer management
Support for jumbo frames up to 10240 bytes
Full duplex flow control with recognition of incoming pause frames and hardware generation of transmitted pause
frames
Half duplex flow control by forcing collisions on incoming frames
Support for 802.1Q VLAN tagging with recognition of incoming VLAN and priority tagged frames
Support for 802.1Qbb priority-based flow control
Programmable Inter Packet Gap (IPG) Stretch
Recognition of IEEE 1588 PTP frames
IEEE 1588 time stamp unit (TSU)
Support for 802.1AS timing and synchronization

EMAC

Supports RMII Interface to the physical layer
Compatible with IEEE Standard 802.3
10 and 100 Mbit/s Operation
Full-duplex and Half-duplex Operation
Statistics Counter Registers
Interrupt Generation to Signal Receive and Transmit Completion
DMA Master on Receive and Transmit Channels
Transmit and Receive FIFOs
Automatic Pad and CRC Generation on Transmitted Frames
Automatic Discard of Frames Received with Errors
Address Checking Logic Supports Up to Four Specific 48-bit Addresses
Supports Promiscuous Mode Where All Valid Received Frames are Copied to Memory
Hash Matching of Unicast and Multicast Destination Addresses
Physical Layer Management through MDIO Interface
Half-duplex Flow Control by Forcing Collisions on Incoming Frames
Full-duplex Flow Control with Recognition of Incoming Pause Frames
Support for 802.1Q VLAN Tagging with Recognition of Incoming VLAN and Priority Tagged Frames
Multiple Buffers per Receive and Transmit Frame
Wake-on-LAN Support
Jumbo Frames Up to 10240 bytes Supported

HSMCI

Compatible with MultiMedia Card Specification Version 4.3
Compatible with SD Memory Card Specification Version 2.0
Compatible with SDIO Specification Version 2.0
Compatible with CE-ATA Specification 1.1
Cards Clock Rate Up to Master Clock Divided by 2
Boot Operation Mode Support
High Speed Mode Support
Embedded Power Management to Slow Down Clock Rate When Not Used
Supports 1 Multiplexed Slot(s)
Each Slot for either a High Speed MultiMedia Card Bus (Up to 30 Cards) or an SD Memory Card
Support for Stream, Block and Multi-block Data Read and Write
Supports Connection to DMA Controller (DMAC)
Minimizes Processor Intervention for Large Buffer Transfers
Built in FIFO (from 16 to 256 bytes) with Large Memory Aperture Supporting Incremental Access
Support for CE-ATA Completion Signal Disable Command
Protection Against Unexpected Modification On -the-Fly of the Configuration Registers

SPI

Supports Communication with Serial External Devices
Master Mode can drive SPCK up to peripheral clock (bounded by maximum bus clock divided by 2)
Slave Mode operates on SPCK, asynchronously to Core and Bus Clock
Four Chip Selects with External Decoder Support Allow Communication with Up to 15 Peripherals
Serial Memories, such as DataFlash and 3-wire EEPROMs
Serial Peripherals, such as ADCs, DACs, LCD Controllers, CAN Controllers and Sensors
External Coprocessors
Master or Slave Serial Peripheral Bus Interface
8-bit to 16-bit Programmable Data Length Per Chip Select
Programmable Phase and Polarity Per Chip Select
Programmable Transfer Delay Between Consecutive Transfers and Delay before SPI Clock per Chip Select
Programmable Delay Between Chip Selects
Selectable Mode Fault Detection
  • Connection to DMA Channel Capabilities Optimizes Data Transfers
One channel for the Receiver, One Channel for the Transmitter

TWI

  • 3 TWIs
  • Compatible with Atmel Two-wire Interface Serial Memory and I2C Compatible Devices
  • One, Two or Three Bytes for Slave Address
  • Sequential Read-write Operations
  • Master, Multi-master and Slave Mode Operation
  • Bit Rate: Up to 400 Kbit/s
  • General Call Supported in Slave mode
  • SMBUS Quick Command Supported in Master Mode
  • Connection to DMA Controller (DMA) Channel Capabilities Optimizes Data Transfers

SSC

  • Provides Serial Synchronous Communication Links Used in Audio and Telecom Applications
  • Contains an Independent Receiver and Transmitter and a Common Clock Divider
  • Interfaced with the DMA Controller (DMAC) to Reduce Processor Overhead
  • Offers a Configurable Frame Sync and Data Length
  • Receiver and Transmitter Can be Programmed to Start Automatically or on Detection of Different Events on the
  • Frame Sync Signal
  • Receiver and Transmitter Include a Data Signal, a Clock Signal and a Frame Synchronization Signal

DBGU

  • System Peripheral to Facilitate Debug of Atmel? ARM?-based Systems
  • Composed of Four Functions
Two-pin UART
Debug Communication Channel (DCC) Support
Chip ID Registers
ICE Access Prevention
  • Two-pin UART
Implemented Features are USART Compatible
Independent Receiver and Transmitter with a Common Programmable Baud Rate Generator
Even, Odd, Mark or Space Parity Generation
Parity, Framing and Overrun Error Detection
Automatic Echo, Local Loopback and Remote Loopback Channel Modes
Interrupt Generation
Support for Two DMA Channels with Connection to Receiver and Transmitter
  • Debug Communication Channel Support
Offers Visibility of COMMRX and COMM TX Signals from the ARM Processor
Interrupt Generation
  • Chip ID Registers
Identification of the Device Revision, Sizes of the Embedded Memories, Set of Peripherals
  • ICE Access Prevention
Enables Software to Prevent System Access Through the ARM Processor’s ICE
Prevention is Made by Asserting the NTRST Line of the ARM Processor’s ICE

UART

  • Two-pin UART
Independent Receiver and Transmitter with a Common Programmable Baud Rate Generator
Even, Odd, Mark or Space Parity Generation
Parity, Framing and Overrun Error Detection
Automatic Echo, Local Loopback and Remote Loopback Channel Modes
Interrupt Generation
Support for Two DMA Channels with Connection to Receiver and Transmitter

USART

  • Programmable Baud Rate Generator
  • 5- to 9-bit Full-duplex Synchronous or Asynchronous Serial Communications
1, 1.5 or 2 Stop Bits in Asynchronous Mode or 1 or 2 Stop Bits in Synchronous Mode
Parity Generation and Error Detection
Framing Error Detection, Overrun Error Detection
MSB- or LSB-first
Optional Break Generation and Detection
By 8 or by 16 Over-sampling Receiver Frequency
Optional Hardware Handshaking RTS-CTS
Receiver Time-out and Transmitter Timeguard
Optional Multidrop Mode with Address Generation and Detection
RS485 with Driver Control Signal
ISO7816, T = 0 or T = 1 Protocols for Interfacing with Smart Cards
NACK Handling, Error Counter with Repetition and Iteration Limit
IrDA Modulation and Demodulation
Communication at up to 115.2 Kbps
  • SPI Mode
Master or Slave
Serial Clock Programmable Phase and Polarity
SPI Serial Clock (SCK) Frequency up to Internal Clock Frequency MCK/6
  • Test Modes
Remote Loopback, Local Loopback, Automatic Echo
  • Supports Connection of:
Two DMA Controller Channels (DMAC)
Offers Buffer Transfer without Processor Intervention

CAN

Fully Compliant with CAN 2.0 Part A and 2.0 Part B
Bit Rates up to 1 Mbit/s
8 Object Oriented Mailboxes with the Following Properties:
CAN Specification 2.0 Part A or 2.0 Part B Programmable for Each Message
Object Configurable in Receive (with Overwrite or Not) or Transmit Modes
Independent 29-bit Identifier and Mask Defined for Each Mailbox
32-bit Access to Data Registers for Each Mailbox Data Object
Uses a 16-bit Timestamp on Receive and Transmit Messages
Hardware Concatenation of ID Masked Bitfields To Speed Up Family ID Processing
16-bit Internal Timer for Timestamping and Network Synchronization
Programmable Reception Buffer Length up to 8 Mailbox Objects
Priority Management between Transmission Mailboxes
Autobaud and Listening Mode
Low Power Mode and Programmable Wake-up on Bus Activity or by the Application
Data, Remote, Error and Overload Frame Handling
Write Protected Registers

PWM

Channels
  • Common Clock Generator Providing Thirteen Different Clocks
A Modulo n Counter Providing Eleven Clocks
Two Independent Linear Dividers Working on Modulo n Counter Outputs
  • Independent Channels
Independent 16-bit Counter for Each Channel
Independent Complementary Outputs with 12-bit Dead-Time Generator (Also Called Dead-Band or Non-Overlapping Time) for Each Channel
Independent Enable Disable Command for Each Channel
Independent Clock Selection for Each Channel
Independent Period, Duty-Cycle and Dead-Time for Each Channel
Independent Double Buffering of Period, Duty-Cycle and Dead-Times for Each Channel
Independent Programmable Selection of The Output Waveform Polarity for Each Channel
Independent Programmable Center or Left Aligned Output Waveform for Each Channel
Independent Output Override for Each Channel
Independent Interrupt for Each Channel, at Each Period for Left-Aligned or Center-Aligned Configuration
2 2-bit Gray Up/Down Channels for Stepper Motor Control
Synchronous Channel Mode
Synchronous Channels Share the Same Counter
Mode to Update the Synchronous Channels Registers after a Programmable Number of Periods
  • 2 Independent Events Lines Intended to Synchronize ADC Conversions
Programmable delay for Events Lines to delay ADC measurements
  • 8 Comparison Units Intended to Generate Interrupts, Pulses on Event Lines
  • 1 Programmable Fault/Break Inputs Providing an Asynchronous Protection of PWM Outputs
4 User Driven through PIO inputs
PMC Driven when Crystal Oscillator Clock Fails
ADC Controller Driven through Configurable Comparison Function
Write Protected Registers

ADC

12-bit Resolution
1 MHz Conversion Rate
Wide Range Power Supply Operation
Selectable Single Ended or Differential Input Voltage
Programmable Gain For Maximum Full Scale Input Range 0 - VDD
  • Resistive 4-wire and 5-wire Touchscreen Controller
Position and Pressure Measurement for 4-wire screens
Position Measurement for 5-wire screens
Average of up to 8 measures for noise filtering
  • Programmable Pen Detection sensitivity
  • Integrated Multiplexer Offering Up to 12 Independent Analog Inputs
  • Individual Enable and Disable of Each Channel
  • Hardware or Software Trigger
External Trigger Pin
Timer Counter Outputs (Corresponding TIOA Trigger)
Internal Trigger Counter
Trigger on Pen Contact Detection
PWM Event Line
Drive of PWM Fault Input
DMA Support
Possibility of ADC Timings Configuration
Two Sleep Modes and Conversion Sequencer
Automatic Wakeup on Trigger and Back to Sleep Mode after Conversions of all Enabled Channels
Possibility of Customized Channel Sequence
  • Standby Mode for Fast Wakeup Time Response
Power Down Capability
  • Automatic Window Comparison of Converted Values
    • Write Protect Registers