查看“MYZR-RK3399-MB314 硬件介绍”的源代码

<div>

= '''接口功能''' =
----
== '''电源接口''' ==
MYZR-RK3399_CB314 模块电源接口定义如下表所示：   
{| class="wikitable"
|-
|管脚号||管脚定义||I/O属性||功能描述
|-
|P1 ~ P9||VCC_SYS||PI||模块工作电源输入，5V/3A
|-
|P10||VCC_RTC||PI||RTC 实时时钟电源输入，3.3V供电
|-
|S10~S12||VCC3V3_SYS||PO||3.3V输出，峰值可达2A
|-
|S13~S15||VCC_1V8||PO||1.8V输出，峰值可达 1A
|-
|S16、S17||VCCA3V0_CODEC0||PO||3.0V输出，峰值可达 300mA
|-
|S18、S19||VCCA1V8_CODEC0||PO||1.8V输出，峰值可达 300mA
|-
|S20||VCC1V8_DVP||PO||1.8V输出，峰值可达 150mA
|-
|P11、P23、P31、P42、P58、P74、P81、P89、P100、P109、P119、P133、P140、P147、P154~P156、
S1~S9、S21、S22、S26、S47、S50、S53、S56、S59、S62、S65、S76、S79、S82、S85、S88、S91、

S94、S97、S100、S103、S106、S108、S110、S112、S115、S118、S121、S124、S127、S130、S133、

S136、S137、S140、S143、S146、S149、S152、S155、S158
|GND||-||地
|}
MYZR-RK3399_CB314 模块使用 VCC_SYS 供电，为保证模块能正常运行，供电电源电压不低于4.6V，不超过 5.5V，供电电流不低于 3A。建议在模块供电端口加一个大于 470uF 的电容。  


== '''多媒体接口''' ==
=== EDP接口===
MYZR-RK3399_CB314 模块eDP接口定义如下表所示：  
{| class="wikitable"
|-
|模块管脚号||模块管脚定义||CPU 管脚号||CPU 管脚定义||I/O属性||功能描述
|-
|S144||EDP_TX3P||D30||EDP_TX3P||O||eDP data lane3 positive output
|-
|S145||EDP_TX3N||D31||EDP_TX3N||O||eDP data lane3 negative output
|-
|S147||EDP_TX2P||C30||EDP_TX2P||O||eDP data lane2 positive output
|-
|S148||EDP_TX2N||C31||EDP_TX2N||O||eDP data lane2 negative output
|-
|S150||EDP_TX1P||B30||EDP_TX1P||O||eDP data lane1 positive output
|-
|S151||EDP_TX1N||A30||EDP_TX1N||O||eDP data lane1 negative output
|-
|S153||EDP_TX0P||B29||EDP_TX0P||O||eDP data lane0 positive output
|-
|S154||EDP_TX0N||A29||EDP_TX0N||O||eDP data lane0 negative output
|-
|S156||EDA_AUXP||B28||EDPAUXP||I/O||eDP CH-AUX positive differential output
|-
|S157||EDA_AUXN||A28||EDPAUXN||I/O||eDP CH-AUX negative differential output
|}
eDP 走线请注意：  
*eDP 信号的参考时钟建在数据中，在接收端还原出时钟信号，所以四组数据差分线对组间不做等长，只需做组内等长处理；  
*为抑制电磁辐射，eDP信号建议PCB内层走线，并保证走线参考面是一个连续完整的参考面，不被分割，否则会造成差分线阻抗的不连续性并引入外部噪声对的影响。如在PCB表层走线，请注意用地线做包地处理；差分对之间不需要伴随地走线；
eDP走线要求如表：  
{| class="wikitable"
|-
|参数||要求
|-
|Trace Impedance||100Ω ±10% differential
|-
|Max intra-pair skew||＜ 4 ps
|-
|Max trace length on carrier board||＜ 6 inch
|-
|Minimum pair to pair spacing||＞ 3 times the width of the trace.Try to increase Spacing between pairs whenever it is possible.
|-
|AC coupling capacitors||100nF ±20%, discrete 0201 package preferable
|-
|The minimum spacing between EDP and other Signals||At least 3 times the width of EDP trace.
|-
|Maximum allowed via||4
|}

=== HDMI接口===
MYZR-RK3399_CB314 模块HDMI接口定义如下表所示：  
{| class="wikitable"
|-
|模块管脚号||模块管脚定义||CPU 管脚号||CPU 管脚定义||I/O属性||功能描述
|-
|S48||I2C3_SDA_3V3||AG6||GPIO4_C0/I2C3_SDA/UART2B_RX_u||IO||I2C data line for HDMI
|-
|S49||I2C3_SCL_3V3||AL2||GPIO4_C1/I2C3_SCL/UART2B_TX_u||IO||I2C clock line for HDMI
|-
|S66||HDMI_CEC||AD7||GPIO4_C7/HDMI_CECINOUT/EDP_HOTPLUG_u||IO||HDMI CEC signal
|-
|S67||HDMI_TXCP||AK16||HDMI_TXCP||O||HDMI positive TMDS differential line driver clock output
|-
|S68||HDMI_TXCN||AL16||HDMI_TXCN||O||HDMI negative TMDS differential line driver clock output
|-
|S69||HDMI_TX0P||AK17||HDMI_TX0P||O||HDMI positive TMDS differential line0 driver data output
|-
|S70||HDMI_TX0N||AL17||HDMI_TX0N||O||HDMI negative TMDS differential line0 driver data output
|-
|S71||HDMI_TX1P||AK18||HDMI_TX1P||O||HDMI positive TMDS differential line1 driver data output
|-
|S72||HDMI_TX1N||AL18||HDMI_TX1N||O||HDMI negative TMDS differential line1 driver data output
|-
|S73||HDMI_TX2P||AK19||HDMI_TX2P||O||HDMI positive TMDS differential line2 driver data output
|-
|S74||HDMI_TX2N||AL19||HDMI_TX2N||O||HDMI negative TMDS differential line2 driver data output
|-
|S75||PORT_HPD||AE15||HDMI_HPD||IO||HDMI hot plug detect signal
|}
HDMI走线请注意：  
*HDMI TX信号的参考时钟为HDMI TXC，所以包括时钟在内的四组差分对都需要做等长处理；  
*HDMI信号需要保证走线参考面是一个连续完整的参考面，不被分割， 否则会造成差分线阻抗的不连续性并引入外部噪声对的影响。在PCB表层走线请注意用地线做整组包地处理； 差分对之间不需要伴随地走线；  
*HDMI信号可以直接顺序扇出到HDMI连接座，走线中应该尽可能的减少换层过孔，过孔会造成线路阻抗的不连续；如果因为模具结构无法避免换层，建议将换层的阻抗变化控制在10%以内，并在每对换层的差分对旁边就近安排一个GND过孔用于信号回流路径的换层；  
*ESD器件靠近HDMI连接座放置；  
*使用带屏蔽层的HDMI线缆，能有效改善EMI问题；  
HDMI走线要求如表：  
{| class="wikitable"
|-
|参数 ||要求
|-
|Trace Impedance ||100Ω ±10%
|-
|Max intra-pair skew ||＜ 4ps
|-
|Max trace length skew between clock and data pairs ||＜ 80ps
|-
|Max trace length on carrier board ||＜ 9.8 inchs
|-
|Minimum pair to pair spacing||＞ 3 times the width of the trace.Try to increase Spacing between pairs whenever it is possible
|-
|The minimum spacing between HDMI and other Signals ||At least 3 times the width of HDMI trace
|-
|Maximum allowed via ||4
|}

=== MIPI接口===
MYZR-RK3399_CB314 模块MIPI接口定义如下表所示： 
*MIPI DSI接口定义  
{| class="wikitable"
|-
|模块管脚号||模块管脚定义||CPU 管脚号||CPU 管脚定义||I/O属性||功能描述
|-
|S51||MIPI_TX0_D3N||AH9||MIPI_TX0_D3N||IO||MIPI DSI negative differential data line3 transceiver output
|-
|S52||MIPI_TX0_D3P||AG9||MIPI_TX0_D3P||IO||MIPI DSI positive differential data line3 transceiver output
|-
|S54||MIPI_TX0_D2N||AH11||MIPI_TX0_D2N||IO||MIPI DSI negative differential data line2 transceiver output
|-
|S55||MIPI_TX0_D2P||AG11||MIPI_TX0_D2P||IO||MIPI DSI positive differential data line2 transceiver output
|-
|S57||MIPI_TX0_CLKN||AH12||MIPI_TX0_CLKN||IO||MIPI DSI negative differential clock line transceiver output
|-
|S58||MIPI_TX0_CLKP||AG12||MIPI_TX0_CLKP||IO||MIPI DSI positive differential clock line transceiver output
|-
|S60||MIPI_TX0_D1N||AH14||MIPI_TX0_D1N||IO||MIPI DSI negative differential data line1 transceiver output
|-
|S61||MIPI_TX0_D1P||AG14||MIPI_TX0_D1P||IO||MIPI DSI positive differential data line1 transceiver output
|-
|S63||MIPI_TX0_D0N||AH15||MIPI_TX0_D0N||IO||MIPI DSI negative differential data line0 transceiver output
|-
|S64||MIPI_TX0_D0P||AG15||MIPI_TX0_D0P||IO||MIPI DSI positive differential data line0 transceiver output
|}
*MIPI CSI/DSI接口定义  
{| class="wikitable"
|-
|模块管脚号||模块管脚定义||CPU 管脚号||CPU 管脚定义||I/O属性||功能描述
|-
|S77||MIPI_TX1/RX1_D1N||AL7||MIPI_TX1/RX1_D1N||IO||MIPI CSI/DSI negative differential data line1 transceiver output
|-
|S78||MIPI_TX1/RX1_D1P||AK7||MIPI_TX1/RX1_D1P||IO||MIPI CSI/DSI positive differential data line1 transceiver output
|-
|S80||MIPI_TX1/RX1_D0N||AL6||MIPI_TX1/RX1_D0N||IO||MIPI CSI/DSI negative differential data line0 transceiver output
|-
|S81||MIPI_TX1/RX1_D0P||AK6||MIPI_TX1/RX1_D0P||IO||MIPI CSI/DSI positive differential data line0 transceiver output
|-
|S83||MIPI_TX1/RX1_D2N||AL9||MIPI_TX1/RX1_D2N||IO||MIPI CSI/DSI negative differential data line2 transceiver output
|-
|S84||MIPI_TX1/RX1_D2P||AK9||MIPI_TX1/RX1_D2P||IO||MIPI CSI/DSI positive differential data line2 transceiver output
|-
|S86||MIPI_TX1/RX1_CLKP||AK8||MIPI_TX1/RX1_CLKP||IO||MIPI CSI/DSI negative differential clock line transceiver output
|-
|S87||MIPI_TX1/RX1_CLKN||AL8||MIPI_TX1/RX1_CLKN||IO||MIPI CSI/DSI positive differential clock line transceiver output
|-
|S89||MIPI_TX1/RX1_D3P||AK10||MIPI_TX1/RX1_D3P||IO||MIPI CSI/DSI negative differential data line3 transceiver output
|-
|S90||MIPI_TX1/RX1_D3N||AL10||MIPI_TX1/RX1_D3N||IO||MIPI CSI/DSI positive differential data line3 transceiver output
|}
*MIPI CSI接口定义  
{| class="wikitable"
|-
|模块管脚号||模块管脚定义||CPU 管脚号||CPU 管脚定义||I/O属性||功能描述
|-
|S92||MIPI_RX0_D0P||AK15||MIPI_RX0_D0P||IO||MIPI CSI positive differential data line0 transceiver output
|-
|S93||MIPI_RX0_D0N||AL15||MIPI_RX0_D0N||IO||MIPI CSI negative differential data line0 transceiver output
|-
|S95||MIPI_RX0_D1P||AK14||MIPI_RX0_D1P||IO||MIPI CSI positive differential data line1 transceiver output
|-
|S96||MIPI_RX0_D1N||AL14||MIPI_RX0_D1N||IO||MIPI CSI negative differential data line1 transceiver output
|-
|S98||MIPI_RX0_CLKP||AK13||MIPI_RX0_CLKP||IO||MIPI DSI positive differential clock line transceiver output
|-
|S99||MIPI_RX0_CLKN||AL13||MIPI_RX0_CLKN||IO||MIPI DSI negative differential clock line transceiver output
|-
|S101||MIPI_RX0_D2P||AK12||MIPI_RX0_D2P||IO||MIPI CSI positive differential data line2 transceiver output
|-
|S102||MIPI_RX0_D2N||AL12||MIPI_RX0_D2N||IO||MIPI CSI negative differential data line2 transceiver output
|-
|S104||MIPI_RX0_D3P||AK11||MIPI_RX0_D3P||IO||MIPI CSI positive differential data line3 transceiver output
|-
|S105||MIPI_RX0_D3N||AL11||MIPI_RX0_D3N||IO||MIPI CSI negative differential data line3 transceiver output
|}
MIPI DSI： <br>
*单MIPI工作模式下，必须使用MIPI_DSI0，即MIPI_TX0这组； MIPI-DSI1不能被单独使用；  <br>
*双MIPI工作模式下，MIPI_TX0和MIPI_TX1/RX1通道可以根据布局以及走线需要，整组调换使用； 

MIPI CSI：  <br>
*RK3399有两组MIPI-CSI输入，均内置ISP处理器，在双MIPI输入的时候可以同时使用。   

MIPI 走线请注意：  
*为抑制电磁辐射， MIPI信号建议PCB内层走线，并保证走线参考面是一个连续完整的参考面，不被分割， 否则会造成差分线阻抗的不连续性并引入外部噪声对的影响。如在PCB表层走线，请注意用地线做包地处理； 差分对之间不需要伴随地走线；  
*MIPI信号在设置走线的延时时，请尽量靠近RK3399端；  

MIPI 走线要求如表：  
{| class="wikitable"
|-
|参数 ||要求
|-
|Trace Impedance ||100Ω ±10% differential
|-
|Max intra-pair skew ||＜ 4ps
|-
|Max trace length skew between clock and data pairs ||＜ 7ps
|-
|Max trace length ||＜ 7.2inch
|-
|Maximum allowed via ||Minimize the number of via in each lane
|-
|Minimum pair to pair spacing ||＞ 3 times the width of the trace.Try to increase Spacing between pairs whenever it is possible.
|-
|The minimum spacing between Mipi and other Signals ||At least 3 times the width of Mipi trace.
|}

=== CIF接口===
MYZR-RK3399_CB314 模块CIF接口定义如下表所示：
{| class="wikitable"
|-
|模块管脚号||模块管脚定义||CPU 管脚号||CPU 管脚定义||I/O属性||功能描述
|-
|P120||CIF_D4||H29||GPIO2_A4/VOP_D4/CIF_D4_d||I||Camera interface input pixel data4
|-
|P121||CIF_D6||H27||GPIO2_A6/VOP_D6/CIF_D6_d||I||Camera interface input pixel data6
|-
|P122||CIF_CLKO||H31||GPIO2_B3/SPI2_CLK/VOP_DEN/CIF_CLKOUTA_u||O||Camera interface output work clock
|-
|P123||CIF_D1||H25||GPIO2_A1/VOP_D1/CIF_D1/I2C2_SCL_u||I||Camera interface input pixel data1
|-
|P124||CIF_D0||G31||GPIO2_A0/VOP_D0/CIF_D0/I2C2_SDA_u||I||Camera interface input pixel data0
|-
|P125||CIF_D7||G30||GPIO2_A7/VOP_D7/CIF_D7/I2C7_SDA_u||I||Camera interface input pixel data7
|-
|P126||DVP_PDN0_H||F31||GPIO2_B4/SPI2_CSn0_u||IO||
|-
|P127||CIF_VSYNC||H28||GPIO2_B0/VOP_CLK/CIF_VSYNC/I2C7_SCL_u||I||Camera interface vertical sync signal
|-
|P128||CIF_D2||H30||GPIO2_A2/VOP_D2/CIF_D2_d||I||Camera interface input pixel data2
|-
|P129||CIF_CLKI||H24||GPIO2_B2/SPI2_TXD/CIF_CLKIN/I2C6_SCL_u||I||Camera interface input pixel clock
|-
|P130||CIF_HREF||F30||GPIO2_B1/SPI2_RXD/CIF_HREF/I2C6_SDA_u||I||Camera interface horizontial sync signal
|-
|P131||CIF_D3||F28||GPIO2_A3/VOP_D3/CIF_D3_d||I||Camera interface input pixel data3
|-
|P132||CIF_D5||F29||GPIO2_A5/VOP_D5/CIF_D5_d||I||Camera interface input pixel data5
|}
</div>